- 您現在的位置：買賣IC網 > PDF目錄16840 > XR20M1170L16-0B-EB (Exar Corporation)EVAL BOARD FOR XR20M1170 16QFN PDF資料下載
參數資料
| 型號： | XR20M1170L16-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 3/56頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR20M1170 16QFN |
| 標準包裝： | 1 |
| 主要目的： | 接口，UART |
| 嵌入式： | 否 |
| 已用 IC / 零件： | XR20M1170 |
| 次要屬性： | I²C & SPI 接口 |
| 已供物品： | 板 |
| 其它名稱： | 1016-1619 XR20M1170L16-0B-EB-ND |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
XR20M1170
11
REV. 1.1.0
I2C/SPI UART WITH 64-BYTE FIFO
2.5
Crystal Oscillator or External Clock Input
The M1170 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The crystal oscillator provides a system clock to the Baud Rate Generators (BRG) section found in
each of the UART. XTAL1 is the input to the oscillator or external clock buffer input with XTAL2 pin being the
output. Please note that the input XTAL1 is not 5V tolerant and so the maximum at the pin should be VCC. For
programming details, see ““Section 2.6, Programmable Baud Rate Generator with Fractional Divisor” on
FIGURE 11. TYPICAL OSCILLATOR CONNECTIONS
C1
22-47 pF
C2
22-47 pF
Y1
1.8432 MHz
to
24 MHz
R1
0-120
(Optional)
R2
500Κ1Μ
XTAL1
XTAL2
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100 ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see Figure 11). The programmable
Baud Rate Generator is capable of operating with a crystal oscillator frequency of up to 24 MHz. However, with
an external clock input on XTAL1 pin, it can extend its operation up to 64 MHz (16 Mbps serial data rate) at
3.3V with an 4X sampling rate. For further reading on the oscillator circuit please see the Application Note
DAN108 on the EXAR web site at http://www.exar.com.
2.6
Programmable Baud Rate Generator with Fractional Divisor
Each UART has its own Baud Rate Generator (BRG) with a prescaler for the transmitter and receiver. The
prescaler is controlled by a software bit in the MCR register. The MCR register bit-7 sets the prescaler to divide
the input crystal or external clock by 1 or 4. The output of the prescaler clocks to the BRG. The BRG further
divides this clock by a programmable divisor between 1 and (216 - 0.0625) in increments of 0.0625 (1/16) to
obtain a 16X, 8X or 4X sampling clock of the serial data rate. The sampling clock is used by the transmitter for
data bit shifting and receiver for data sampling. The BRG divisor (DLL, DLM and DLD registers) defaults to the
value of ’1’ (DLL = 0x01, DLM = 0x00 and DLD = 0x00) upon power-up. Therefore, the BRG must be
programmed during initialization to the operating data rate. The DLL and DLM registers provide the integer part
of the divisor and the DLD register provides the fractional part of the dvisior. The four lower bits of the DLD are
used to select a value from 0 (for setting 0000) to 0.9375 or 15/16 (for setting 1111). Programming the Baud
Rate Generator Registers DLL, DLM and DLD provides the capability for selecting the operating data rate.
Table 6 shows the standard data rates available with a 24MHz crystal or external clock at 16X clock rate. If the
pre-scaler is used (MCR bit-7 = 1), the output data rate will be 4 times less than that shown in Table 6. At 8X
sampling rate, these data rates would double and at 4X sampling rate, these data rates would quadruple. Also,
when using 8X sampling mode, the bit time will have a jitter of ± 1/16 whenever the DLD is non-zero and is an
相關PDF資料 |
PDF描述 |
|---|---|
| RPP30-4824S-1F | CONV DC/DC 30W 36-75VIN 24VOUT |
| 462A023-4/86-0 | BOOT MOLDED |
| MLF2012E6R8J | INDUCTOR MULTILAYER 6.8UH 0805 |
| XR20M1170G24-0B-EB | EVAL BOARD FOR XR20M1170 24TSSOP |
| XR20M1172L32-0A-EB | EVAL BOARD FOR XR20M1172 32QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR20M1170L24-0A-EB | 功能描述:UART 接口集成電路 Supports M1170 24pin QFN, I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20M1170L24-0B-EB | 功能描述:UART 接口集成電路 Supports M1170 28pin QFN, SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20M1170L28-0A-EB | 功能描述:UART 接口集成電路 Supports M1170 28pin QFN, I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR20M1170L28-0B-EB | 功能描述:界面開發(fā)工具 Supports M1170 28pin QFN, SPI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR20M1172 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO |
發(fā)布緊急采購，3分鐘左右您將得到回復。