- 您現在的位置：買賣IC網 > PDF目錄376457 > XR88C192 (Exar Corporation) DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER PDF資料下載
參數資料
| 型號： | XR88C192 |
| 廠商： | Exar Corporation |
| 英文描述： | DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| 中文描述： | 兩路通用異步接收器和發射 |
| 文件頁數： | 20/32頁 |
| 文件大?。?/td> | 186K |
| 代理商： | XR88C192 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
XR88C92/192
20
Rev. 1.31
following table shows how to select the clock source for
the C/T when used in counter mode or timer mode.
condition (see MR0A bit-6 and MR1A bit-6). For ex-
ample, if a RX trigger level of '6' is chosen, this bit will
be set whenever the RX FIFO contains six or more
bytes. This bit can be cleared by reading the data out
of the FIFO till it falls below the trigger level.
ISR Bit-2:
Channel A change in break.
This bit is set when channel A receiver detects the
beginning or the end of a break condition. It is reset
when the CPU issues a channel A reset break change
interrupt command (CRA bits 7-4 = 0x5).
ISR Bit-3: Counter/Timer (C/T) ready.
In counter mode, this bit is set when the C/T reaches
terminal count. In timer mode, this bit is set each time
the C/T output switches from low to high (rising edge -
see Figure 2). In either mode, this bit is cleared by a stop
counter command.
ISR Bit-4: Transmit ready B.
This bit is set when channel B's transmit buffer (FIFO)
is filled below the programmed transmit trigger level (see
MR0B bits 5-4). For example, if a TX trigger level of '4'
is chosen, this bit will be set whenever the TX FIFO has
four or more empty locations. This bit can be cleared by
loading the TX FIFO above the trigger level.
ISR Bit-5: Receive ready B.
This bit is set when channel B's receive buffer (FIFO)
is filled above the programmed receive trigger level
condition (see MR0B bit-6 and MR1B bit-6). For ex-
ample, if a RX trigger level of '6' is chosen, this bit will
be set whenever the RX FIFO contains six or more
bytes. This bit can be cleared by reading the data out
of the FIFO till it falls below the trigger level.
ISR Bit-6. Channel B change in break.
This bit is set when channel B receiver detects the
beginning or the end of a break condition. It is reset
when the CPU issues a channel B reset break change
interrupt command (CRB bits 7-4 = 0x5).
ISR Bit-7. Input port change status.
This bit is set when a change of state has occurred at
the IP0, IP1, IP2, or IP3 inputs, and that event has been
enabled to cause an interrupt by programming ACR Bits
3-0. This bit is cleared when the CPU reads the input port
change register.
INTERRUPT MASK REGISTER (IMR)
This register selects which bits in the interrupt status
register can cause an interrupt output. If a bit in the
interrupt status register is a “1” and the corresponding
ACR
Bits 6:4
0 0 0
0 0 1
0 1 0
0 1 1
C/T
Mode
Counter
Counter
Counter
Counter
Clock Source
External (IP2)
TXAClk1-Transmit A 1X clock
TXBClk1-Transmit B 1X clock
Crystal or External Clock
(XTAL1/Clk) Divided by 16
External (IP2)
External (IP2) Divided by 16
Crystal or External Clock
(XTAL1/Clk)
Crystal or External Clock
(XTAL1/Clk) Divided by 16
1 0 0
1 0 1
1 1 0
Timer
Timer
Timer
1 1 1
Timer
ACR Bit-7: Baud rate table Select.
This bit is used to select between two sets of baud rate
tables. See Baudrate table on Page 18. It should be
changed only after both channels have been reset and
disabled.
0 = Set 1
1 = Set 2
INTERRUPT STATUS REGISTER (ISR)
This register provides the status of all potential interrupt
sources. The contents of this register are logically
“AND”-ed with the contents of the interrupt mask regis-
ter, and the results are “OR”-ed. The resulting signal is
inverted to produce the -INT output.
All active nterrupt
sources are visible by reading the SR, regardless of
the contents of the nterrupt mask register.
Reading
the ISR has no effect on any interrupt source. Each
active interrupt source must be cleared in a source-
specific fashion to clear the ISR. All interrupt sources
are cleared when the XR88C92/192 is reset.
4
ISR Bit-0:
Transmit ready A.
This bit is set when channel A's transmit buffer (FIFO)
is filled below the programmed transmit trigger level (see
MR0A bits 5-4). For example, if a TX trigger level of '4'
is chosen, this bit will be set whenever the TX FIFO has
four or more empty locations. This bit can be cleared by
loading the TX FIFO above the trigger level.
ISR Bit-1:
Receive ready A .
This bit is set when channel A's receive buffer (FIFO)
is filled above the programmed receive trigger level
相關PDF資料 |
PDF描述 |
|---|---|
| XR88C192CJ | DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C192CP | DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C192CV | DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C192IJ | DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C192IP | DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR88C192CJ | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C192CJ-0A-EVB | 功能描述:界面開發工具 Supports 88C192 44ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR88C192CJ-F | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR88C192CP | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C192CV | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
發布緊急采購，3分鐘左右您將得到回復。