- 您現在的位置：買賣IC網 > PDF目錄3762 > XR88C92CVTR-F (Exar Corporation)IC UART FIFO DUAL 44LQFP PDF資料下載
參數資料
| 型號： | XR88C92CVTR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 2/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO DUAL 44LQFP |
| 標準包裝： | 1,000 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 16 字節 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LQFP |
| 供應商設備封裝： | 44-LQFP（10x10） |
| 包裝： | 帶卷 (TR) |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
XR88C92/192
10
Rev. 1.33
This is also reflected in the Interrupt Status Register,
ISR bit-0 for channel A and bit-4 for channel B. This is
different from the TxRDY bit in the status register.
The TxRDY bit in the status register (SRA, SRB bit-2)
indicates if the TX FIFO has at least one empty location.
This can also be programmed to appear at the output pin
OP6/OP7. The TxEMT bit (SRA, SRB bit-3) indicates if
both the TX FIFO and the TX Shift Register are empty.
The transmitter can be reset through a software com-
mand (CRA, CRB bits 7:4). If it is reset, operation
ceases immediately and must be enabled through the
command register before resuming operation. Reset
also discards any characters in the FIFO.
RECEIVER
The channel A and B receivers are enabled for data
reception through the respective channels command
register (CRA, CRB bits 1:0). The channels receiver
looks for the high-to-low (mark-to-space) transition of a
start bit on the receiver serial-data input pin. If operating
in 16X clock mode, the serial input data is re-sampled
on the next 7 clocks. If the receiver serial data is
sampled high, the start bit is invalid and the search for
a valid start bit begins again. If receiver serial data is still
low, a valid start bit is assumed and the receiver
continues to sample the input at one bit time intervals
(at the theoretical center of the bit) until the proper
number of data bits and the parity bit (if any) have been
assembled and one stop bit has been detected. If an 1X
clock is used, data is sampled at one bit time intervals
throughout, including the start bit. Data on the receiver
serial data input pin is sampled on the rising edge of the
programmed clock source (XTAL1, IP4 or IP6: see CSR
bits 7:4).
In this process, the least significant bit is received first.
The receiver buffer is composed of the FIFO (8/16
locations in XR88C92/192 respectively) and a receive
shift register connected to the receiver serial-data input.
Data is assembled in the shift register and loaded into
the bottom most empty FIFO location. If the character
length is less than eight bits, the most significant unused
bits are set to zero.
If the stop bit is sampled as a 1, the receiver will
immediately look for the next start bit. However, if the
stop bit is sampled as a 0, either a framing error or a
received break has occurred. If the stop bit is 0 and the
data and parity (if any) are not all zero, it is a framing
error. The damaged character is transferred to the FIFO
with the framing error flag set. If the receiver serial data
remains low for one-half of the bit period after the stop
bit was sampled, the receiver operates as if a new start
bit transition has been detected. If the stop bit is 0 and
the data and parity (if any) bits are also all zero, it is a
break. A character consisting of all zeros will be loaded
into the the FIFO with the received-break bit (but not the
framing error bit) set to one. The receiver serial-data
input must return to a high condition for at least one-half
bit time before a search for the next start bit begins.
Also, at this time, the received break bit is reset.
The receiver can detect a break that starts in the middle
of a character provided the break persists completely
through the next character time or longer. When the
break begins in the middle of a character, the receiver
will place the damaged character in the FIFO with the
framing error bit set. Then, provided the break persists
through the next character time, the receiver will also
place an all-zero character in the FIFO with the re-
ceived-break bit set. The parity error, framing error,
overrun error, and received-break conditions (if any)
set error and break flags in the status register at the
received character boundary and are valid only when
the receiver-ready bit (RXRDY) in the status register is
set.
The receiver-ready bit in the status register (SRA, SRB
bit-0) is set whenever one or more characters are
available to be read by the CPU. A read of the receiver
buffer produces an output of data from the top of the
FIFO stack. After the read cycle, the data at the top of
the FIFO stack and its associated status bits are
“popped” and new data can be added at the bottom of
the stack by the receive shift register. The FIFO-full
status bit (SRA, SRB bit-1) is set if all 8 (or 16) stack
positions are filled with data. Either the receiver-ready or
the FIFO-full status bits can be selected to cause an
interrupt (see MR1A, MR1B bit-6).
In addition to the data byte, three status bits (parity error,
framing error, and received break) are appended to
each data character in the FIFO (overrun is not). By
programming the error-mode control bit (MR1A, MR1B
bit-5), status can be provided for “character” or “block”
modes. In the “character” mode, the status register
(SRA, SRB) is updated on a character-by-character
basis and applies only to the character at the top of the
FIFO. Thus, the status must be read before the charac-
ter is read. Reading the character pops the data byte
and its error flags off the FIFO. In the “block” mode, the
status provided in the status register for the parity error,
相關PDF資料 |
PDF描述 |
|---|---|
| XR88C92CJTR-F | IC UART FIFO DUAL 44PLCC |
| ST16C452CJ68TR-F | IC UART W/PAR PORT DUAL 68PLCC |
| ST16C552CJ68TR-F | IC UART FIFO 16B DUAL 68PLCC |
| XR68C681CJTR-F | IC UART CMOS DUAL 44PLCC |
| ST16C2550CJ44TR-F | IC UART FIFO 16B DUAL 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR88C92IJ | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C92IJ-F | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR88C92IJTR-F | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR88C92IP | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C92IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
發布緊急采購，3分鐘左右您將得到回復。