- 您現在的位置：買賣IC網 > PDF目錄376460 > XRT5897ES (Exar Corporation) () PDF資料下載
參數資料
| 型號： | XRT5897ES |
| 廠商： | Exar Corporation |
| 英文描述： | () |
| 中文描述： | （） |
| 文件頁數： | 3/12頁 |
| 文件大小： | 401K |
| 代理商： | XRT5897ES |
XRT5897ES
3
Rev. 1.00
Signal Name
Ribbon Cable
Connector Pin
Test Point Name
Receiver 1 loss of signal output
1
LOS1
Receiver 1 positive data output
2
RXPOS1
Ground
3
-
Receiver 1 negative data output
4
RXNEG1
Ground
5
-
Transmitter 1 positive data input
6
TXPOS1
Ground
7
-
Transmitter 1 negative data input
8
TXNEG1
Ground
9
-
Transmitter 1 clock input
10
TXCLK1
Table 1. Equipment-side Signal Connections
Note:
Installing the two jumpers next to a ribbon cable connector implements an equipment-side
loopback on that channel.
Transmitter Line Output and Receiver Line Input Connections
Three-circuit one quarter inch audio-type jacks are used for the transmitter line-side output and
receiver line-side input of each channel. These jacks accept the patch cord plugs that are
commonly used for interconnecting the120 Ohm balanced lines that are used with E1 test
equipment.
Loopback Provisions
A signal source capable of transmitting and receiving dual-rail data having TTL or 3.3 V CMOS
compatible levels is necessary in order to test the XRT5897 receivers and transmitters
individually. Commercially-available E1 test sets normally do not operate with these signals.
However, an equipment-side loopback permits operation of the demo board with readily
available test equipment. This loopback may be implemented on any channel by installing the
two jumper shunts located next to the 10-pin ribbon cable connector for that channel. If these
shunts are installed on Channel 1, the receiver outputs RXPOS1 and RXNEG1 are connected
to the transmitter inputs TXPOS1 and TXNEG1 respectively. Now, Channel 1 may be tested
by connecting the output of an E1 pattern generator to the Channel 1 receiver input, RX1, and
the 120 Ohm input of an error detector to the Channel 1 transmitter output, TX1.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT5897 | Seven-Channel E1 Line Interface (3.3V or 5.0V)(七通道E1 3.3V線接口單元) |
| XRT5997 | Seven-Channel E1 Line Interface Unit(7通道 E1線接口單元) |
| XRT59L91 | Single-Chip E1 Line Interface Unit(單片E1 線接口單元) |
| XRT59L921 | TWENTY-ONE CHANNEL E1 LINE INTERFACE UNIT |
| XRT59L921IB | TWENTY-ONE CHANNEL E1 LINE INTERFACE UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT5897IV | 功能描述:外圍驅動器與原件 - PCI 7CH E1 LIU RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT5897IV-F | 功能描述:外圍驅動器與原件 - PCI 7 Ch.E1LIU3.3/5.5V RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XR-T5990CN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Pulse Telephone Dialer |
| XR-T5990CP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Pulse Telephone Dialer |
| XR-T5992CN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Pulse Telephone Dialer |
發布緊急采購，3分鐘左右您將得到回復。