- 您現在的位置：買賣IC網 > PDF目錄376462 > XRT75L06 (Exar Corporation) SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR PDF資料下載
參數資料
| 型號： | XRT75L06 |
| 廠商： | Exar Corporation |
| 英文描述： | SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| 中文描述： | 六通道E3/DS3/STS-1線路接口單元與抖動衰減器 |
| 文件頁數： | 47/63頁 |
| 文件大小： | 360K |
| 代理商： | XRT75L06 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
XRT75L06
REV. 1.0.3
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
44
6.2
Whether the LIU is configured for Asynchronous or Synchronous mode, the following descriptions apply. The
synchronous mode requires an input clock (PCLK) to be used as the microprocessor timing reference. Read
and Write operations are described below.
Read Cycle (For Pmode = "0" or "1")
Whenever the local μP wishes to read the contents of a register, it should do the following.
1.
Place the address of the target register on the address bus input pins Addr[7:0].
2.
While the μP is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables communication between the μP and
the LIU microprocessor interface block.
3.
Next, the μP should indicate that this current bus cycle is a Read operation by toggling the RD input pin
"Low". This action enables the bi-directional data bus output drivers of the LIU.
4.
After the μP toggles the Read signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
to inform the μP that the data is available to be read by the μP, and that it is ready for the next command.
5.
After the μP detects the RDY signal and has read the data, it can terminate the Read Cycle by toggling the
RD input pin "High".
6.
The CS input pin must be pulled "High" before a new command can be issued.
Write Cycle (For Pmode = "0" or "1")
Whenever a local μP wishes to write a byte or word of data into a register within the LIU, it should do the follow-
ing.
1.
Place the address of the target register on the address bus input pins Addr[7:0].
2.
While the μP is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables communication between the μP and
the LIU microprocessor interface block.
3.
The μP should then place the byte or word that it intends to write into the target register, on the bi-direc-
tional data bus D[7:0].
4.
Next, the μP should indicate that this current bus cycle is a Write operation by toggling the
WR
input pin
"Low". This action enables the bi-directional data bus input drivers of the LIU.
5.
After the μP toggles the Write signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
to inform the μP that the data has been written into the internal register location, and that it is ready for the
next command.
6.
The CS input pin must be pulled "High" before a new command can be issued.
A
SYNCHRONOUS
AND
S
YNCHRONOUS
D
ESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| XRT75L06IB | SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75R03D | THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER |
| XRT75R03DIV | THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER |
| XRT75R03 | THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75R03IV | THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT75L06D | 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75L06DES | 功能描述:時鐘合成器/抖動清除器 6CH T3/E3/STS1 LIU+DESYNCH 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75L06DIB | 功能描述:接口 - 專用 6CH E3/DS3/STS1 LIU w/DeSynch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| XRT75L06DIB-F | 功能描述:外圍驅動器與原件 - PCI 6-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT75L06ES | 功能描述:時鐘合成器/抖動清除器 6 CHT3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。