參數資料
型號： XRT81L27IV-F
廠商： Exar Corporation
文件頁數： 8/30頁
文件大小： 0K
描述： IC LIU EI 7CH 3.3V 128TQFP
標準包裝： 72
應用： DECT
接口： 串行
電源電壓： 3.3V
封裝/外殼： 128-LQFP
供應商設備封裝： 128-TQFP（14x20）
包裝： 托盤
安裝類型： 表面貼裝
XRT81L27
á
SEVEN CHANNEL E1 LINE INTERFACE UNIT WITH CLOCK RECOVERY
REV. 1.1.0
14
Once the CS input pin has been asserted, the type of
operation and the target register address must be
specified. This information is supplied to the MSI by
writing eight serial bits of information into the SDI in-
put. Each of these bits is clocked into the MSI from
the SDI input on the rising edge of SCLK. These eight
bits are identified and described next.
Bit 1 - R/W (Read/Write) Bit
This bit is clocked into the SDI input on the first rising
edge of SCLK after CS has been asserted. This bit
indicates whether the current operation is a Read or
Write operation. A “1” in this bit specifies a Read from
the XRT81L27, a “0” in this bit specifies a Write to the
device.
Bits 2 through 5: The four (4) bit Address Values
(labeled A0, A1, A2 and A3)
The next four rising edges of the SCLK provide the 4-
bit address value for this operation. The address se-
lects the appropriate Command/Control Register in
the XRT81L27. The address bits must be supplied to
the SDI input pin in ascending order with the LSB
(least significant bit) first.
Bits 6 and 7:
The next two bits, (A4 and A5) must be set to “0” as
shown in Figure 6.
Bit 8:
The value of A6 is a “don’t care” but must be clocked.
1.1.2
Data phase of the (MSI) operation
The Microprocessor Serial Interface (MSI) must next
be supplied with 8 additional clocks with the relative
timing of Figure 5. Table 10 provides essential values
for both the selection and data phases of the MSI op-
eration. If the operation specified is a Read, the
XRT81L27 will output data on the SDO pin from the
addressed register. Data is output in ascending order
with the LSB first
If a Write operation has been activated, the external
hardware/Micro must supply the first seven (7) bits to
be written into the selected register. The eighth bit is
a “Don’t care” as only seven bits are used in each of
the registers. These bits are input LSB first.
At the end of the serial shift phase the data is loaded
in parallel into the addressed register. If any register
bit was already set, that bit must be included in the in-
put bit stream. Therefore one must either keep an im-
age of the register status in the micro or do a “read-
modify-write” operation to maintain the state of each
bit that isn’t changing.
FIGURE 5. TIMING DIAGRAM FOR THE MICROPROCESSOR SERIAL INTERFACE
SDI
R/W
A1
A0
CS
SCLK
CS
SCLK
SDI
SDO
D0
D1
D2
D7
t22
t21
t23
t24
t25
t26
t27
t28
t29
t30
t31
t32
t33
Hi-Z
相關PDF資料
PDF描述
XRT82D20IW-F IC LIU E1 SGL 28SOJ
XRT82L24AIV-F IC LIU E1 QAUD 100TQFP
XRT83D10IW IC LIU T1/E1 SGL 28SOJ
XRT83L30IV-F IC LIU LH/SH T1/E1 SGL 64TQFP
XRT83L314IB-L IC LIU T1/E1/J1 14CH 304TBGA
相關代理商/技術參數
參數描述
XR-T8205CP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telephone Ringer
XR-T8205P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telephone Ringer
XRT82D20 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL E1 LINE INTERFACE UNIT
XRT82D20_06 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL E1 LINE INTERFACE UNIT
XRT82D20ES 功能描述:外圍驅動器與原件 - PCI 1 CH E1 LIU RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*