參數資料
型號： XTR110KU
英文描述： PRECISION VOLTAGE-TO-CURRENT CONVERTER/TRANSMITTER
中文描述： 精密的電壓電流轉換器/變送器
文件頁數： 6/9頁
文件大?。?/td> 148K
代理商： XTR110KU
6
XTR110
If the supply voltage, +V
CC
, exceeds the gate-to-source
breakdown voltage of Q
EXT
, and the output connection
(drain of Q
EXT
) is broken, Q
EXT
could fail. If the gate-to-
source breakdown voltage is lower than +V
CC
, Q
EXT
can be
protected with a 12V zener diode connected from gate to
source.
Two PNP discrete transistors (Darlington-connected) can be
used for Q
EXT
—see Figure 2. Note that an additional capaci-
tor is required for stability. Integrated Darlington transistors
are not recommended because their internal base-emitter
resistors cause excessive error.
TRANSISTOR DISSIPATION
Maximum power dissipation of Q
EXT
depends on the power
supply voltage and full-scale output current. Assuming that
the load resistance is low, the power dissipated by Q
EXT
is:
P
MAX
= (+V
CC
) I
FS
The transistor type and heat sinking must be chosen accord-
ing to the maximum power dissipation to prevent overheat-
ing. See Table II for general recommendations.
(2)
PACKAGE TYPE
ALLOWABLE POWER DISSIPATION
TO-92
TO-237
TO-39
TO-220
TO-3
Lowest: Use minimum supply and at +25
°
C.
Acceptable: Trade-off supply and temperature.
Good: Adequate for majority of designs.
Excellent: For prolonged maximum stress.
Use if hermetic package is required.
TABLE II. External Transistor Package Type and
Dissipation.
INPUT VOLTAGE RANGE
The internal op amp A
1
can be damaged if its non-inverting
input (an internal node) is pulled more than 0.5V below
common (0V). This could occur if input pins 3, 4 or 5 were
driven with an op amp whose output could swing negative
under abnormal conditions. The voltage at the input of A
1
is:
V
A1
= + +
(3)
This voltage should not be allowed to go more negative than
–0.5V. If necessary, a clamp diode can be connected from
the negative-going input to common to clamp the input
voltage.
COMMON (Ground)
Careful attention should be directed toward proper con-
nection of the common (grounds). All commons should
be joined at one point as close to pin 2 of the XTR110 as
possible. The exception is the I
OUT
return. It can be
returned to any point where it will not modulate the
common at pin 2.
VOLTAGE REFERENCE
The reference voltage is accurately regulated at pin 12
(V
REF
SENSE
). To preserve accuracy, any load including pin
(V
)
16
(V
)
4
(V
IN2
)
2
FIGURE 2. Q
EXT
Using PNP Transistors.
XTR110
47nF
R
L
I
OUT
1
13
14
+V
CC
16
2
2N2907
etc.
TIP30B
etc.
0.047μF
Common
3 should be connected to this point. The circuit in Figure 3
shows adjustment of the voltage reference.
The current drive capability of the XTR110’s internal refer-
ence is 10mA. This can be extended if desired by adding an
external NPN transistor shown in Figure 4.
OFFSET (ZERO) ADJUSTMENT
The offset current can be adjusted by using the potentiom-
eter, R
1
, shown in Figure 5. Set the input voltage to zero and
then adjust R
1
to give 4mA at the output. For spans starting
FIGURE 4. Increasing Reference Current Drive.
XTR110
15
12
+V
CC
16
2
Sense
Force
For 100mA with V
up to
40V use 2N3055 for Q
REF
.
Q
REF
+10V
REF
FIGURE 3. Optional Adjustment of Reference Voltage.
XTR110
V
REF
Adjust
15
12
11
V
REF
Sense
V
REF
Force
+V
CC
16
Common
2
V
REF
R
20k
R
S
(1)
Adjust Range
±5% Optimum
NOTE: (1) R
S
gives higher resolution with reduced
range, set R
S
= 0
for larger range.
相關PDF資料
PDF描述
XTR110 A/D Converter (A-D) IC; Resolution (Bits):24; Sample Rate:606SPS; Input Channels Per ADC:2; Input Channel Type:Differential; Data Interface:Serial, 3-Wire; Package/Case:20-DIP; Interface Type:Serial; Leaded Process Compatible:No RoHS Compliant: No
XTR110AG PRECISION VOLTAGE-TO-CURRENT CONVERTER/TRANSMITTER
XTR112 4-20mA CURRENT TRANSMITTERS with Sensor Excitation and Linearization
XTR114 4-20mA CURRENT TRANSMITTERS with Sensor Excitation and Linearization
XTR114UA Connector assemblies, Mouse Computer cables; Connector Type A:DB9 Male; Connector Type B:DB9 Female; Cable Length:25ft
相關代理商/技術參數
參數描述
XTR110KU 制造商:Texas Instruments 功能描述:VOLT/CURRENT CONVERTER SOIC16 110
XTR110KU/1K 功能描述:電流靈敏放大器 Prec Vltg-To-Crnt Cnertr/Trnsmtr RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel
XTR110KU/1KG4 功能描述:電流靈敏放大器 Prec Vltg-To-Crnt Cnertr/Trnsmtr RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel
XTR110KUG4 功能描述:電流靈敏放大器 Prec Vltg-To-Crnt Cnertr/Trnsmtr RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel
XTR110L 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCC Precision Voltage-to-Current Converter/Transmitter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*