參數資料
型號： YNC12S20-0G
廠商： POWER-ONE INC
元件分類： 電源模塊
英文描述： 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
封裝： ROHS COMPLIANT PACKAGE-5
文件頁數： 25/28頁
文件大?。?/td> 337K
代理商： YNC12S20-0G
ZD-02137 Rev. 2.1 21-Jun-10
Page 6 of 28
www.power-one.com
YNC12S20 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 20 A
Vin
Rw
Rload
Vin
GND
ON/OFF
(Top View)
Converter
TRIM
SENSE
Vout
Nex -c Series
TM
Fig. B: Remote sense circuit configuration.
Because the sense lead carries minimal current,
large traces on the end-user board are not
required. However, sense traces should be
located close to a ground plane to minimize
system noise and ensure optimum performance.
When utilizing the remote sense feature, care
must be taken not to exceed the maximum
allowable output power capability of the converter,
equal to the product of the nominal output voltage
and the allowable output current for the given
conditions.
When using remote sense, the output voltage at
the converter can be increased up to 0.5V above
the nominal rating in order to maintain the required
voltage across the load. Therefore, the designer
must, if necessary, decrease the maximum current
(originally obtained from the derating curves) by
the same percentage to ensure the converter’s
actual output power remains at or below the
maximum allowable output power.
Output Voltage Programming (Pin 3)
The output voltage can be programmed from
0.7525V to 5.5V by connecting an external resistor
between TRIM pin (Pin 3) and GND pin (Pin 5);
see Fig. C.
A trim resistor, RTRIM, for a desired output voltage
can be calculated using the following equation:
1
0.7525)
-
(V
5
.
10
R
REQ
-
O
RIM
T
[k
]
where,
TRIM
R
Required value of trim resistor [k
]
REQ
O
V
Desired (trimmed) output voltage [V]
Vin
R
TRIM
Rload
Converter
Vin
GND
ON/OFF
(Top View)
TRIM
Vout
SENSE
Nex -c Series
TM
Fig. C: Configuration for programming output voltage.
Note that the tolerance of a trim resistor directly
affects the output voltage tolerance. It is
recommended to use standard 1% or 0.5%
resistors; for tighter tolerance, two resistors in
parallel are recommended rather than one
standard value from Table 1.
The ground pin of the trim resistor should be
connected directly to the converter GND pin (Pin
5) with no voltage drop in between. Table 1
provides the trim resistor values for popular output
voltages.
Table 1: Trim Resistor Value
V0-REG [V]
RTRIM [k]
The Closest
Standard Value [k]
0.7525
open
1.0
41.2
1.2
22.46
22.6
1.5
13.0
1.8
9.0
9.09
2.0
7.4
7.32
2.5
5.0
4.99
3.3
3.12
3.09
5.0
1.47
5.5
1.21
The output voltage can be also programmed by
external voltage source. To make trimming less
sensitive, a series external resistor Rext is
recommended between the TRIM pin and the
programming voltage source. Control Voltage can
be calculated by the formula:
15
0.7525)
-
)(V
R
1
(
7
.
0
V
REQ
-
O
EXT
CTRL
[V]
where,
相關PDF資料
PDF描述
YNC12S20-DS1 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
YNC12S20-D 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
YNC12S20-DG 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
YNC12S20-0S1G 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
YNC12S20-0 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
YNC12S20A-0 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A
YNC12S20A-0G 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A
YNC12S20A-D 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A
YNC12S20A-DG 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A
YNC12S20-D 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*