- 您現在的位置：買賣IC網 > PDF目錄48107 > YNV12T10025-D-G (POWER-ONE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | YNV12T10025-D-G |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT |
| 文件頁數： | 22/26頁 |
| 文件大?。?/td> | 417K |
| 代理商： | YNV12T10025-D-G |
OCT 24, 2006 revised to APR 10, 2007
Page 5 of 26
www.power-one.com
YNV12T100xy DC-DC Converter Family Data Sheet
9.6-14 VDC Input; 1.0 -5.0 VDC Output @ 10 A
Operation
Input and Output Impedance
YNV12T100xy converters should be connected via
a low impedance to the DC power source. In many
applications, the inductance associated with the
distribution from the power source to the input of
the converter can affect the stability of the
converter. It is recommended to use decoupling
capacitors in order to ensure stability of the
converter and reduce input ripple voltage. The
converter has an internal input capacitance of
20 μF with very low ESR ceramic capacitors.
In a typical application, low - ESR tantalum or
POS capacitors will be sufficient to provide
adequate ripple voltage filtering and at the input of
the converter. However, very low ESR ceramic
capacitors 47μF-100μF are recommended at the
input of the converter in order to minimize the
input ripple voltage. They should be placed as
close as possible to the input pins of the converter.
The YNV12T100xy has been designed for stable
operation with or without external capacitance.
Low ESR ceramic capacitors placed as close as
possible to the load (Min 47μF) are recommended
for improved transient performance and lower
output voltage ripple.
It is important to keep low resistance and low
inductance PCB traces when connecting the load
to the output pins of the converter in order to
maintain good load regulation.
ON/OFF (Pin 10)
The ON/OFF pin is used to turn the power
converter on or off remotely via a system signal.
There are two remote control options available,
positive logic (standard option) and negative logic,
and both are referenced to GND. Typical
connections are shown in Fig. A.
The positive logic version turns the converter on
when the ON/OFF pin is at a logic high or left
open, and turns the converter off when at a logic
low or shorted to GND.
Rload
Vin
CONTROL
INPUT
Vin
GND
ON/OFF
(Top View)
Converter
R*
R* is for negative logic option only
Nex -v Series
TM
TRIM
Vout
SENSE
GND
6
5
Fig. A: Circuit configuration for ON/OFF function.
The negative logic version turns the converter on
when the ON/OFF pin is at a logic low or left open,
and turns the converter off when the ON/OFF pin
is at a logic high or connected to Vin.
ON/OFF pin is internally pulled-up to Vin for
positive logic version, and pulled-down for
negative logic version. A TTL or CMOS logic gate,
open collector (open drain) transistor can be used
to drive ON/OFF pin. When using open collector
(open drain) transistor with a negative logic option,
add a pull-up resistor (R*) of 75K to Vin as shown
in Fig. A; This device must be capable of:
- sinking up to 0.2 mA at a low level voltage of
≤ 0.8V
- sourcing up to 0.25 mA at a high logic level of
2.3V – 5V
- sourcing up to 0.75 mA when connected to Vin.
Remote Sense (Pin 3)
The remote sense feature of the converter
compensates for voltage drops occurring only
between Vout pins of the converter and the load.
The SENSE pin (Pin 3) should be connected at
the load or at the point where regulation is
required (see Fig. B). There is no sense feature on
the output GND return pin, where the solid ground
plane should provide low voltage drop.
If remote sensing is not required, the SENSE pin
must be connected to any of the Vout pins to
ensure the converter will regulate at the specified
output voltage. If these connections are not made,
the converter will deliver an output voltage that is
slightly higher than the specified value.
相關PDF資料 |
PDF描述 |
|---|---|
| YNV12T10025-D | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10033-D-G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10050-D-G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10015-0-G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10015-D | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| YNV12T10033-0 | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV12T10033-0G | 制造商:Power-One 功能描述:Module DC-DC 1-OUT 3.3V 10A 50W 10-Pin SIP 制造商:Power-One 功能描述:YNV12T Series 50 W Single Output 3.3 V DC/DC Converter Power Supply |
| YNV12T10033-D | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV12T10033-D02G | 制造商:Power-One 功能描述: |
| YNV12T10033-D03G | 制造商:Power-One 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。