- 您現在的位置：買賣IC網 > PDF目錄48109 > YS12S10-0 (POWER-ONE INC) DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | YS12S10-0 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封裝： | MODULE-6 |
| 文件頁數： | 26/27頁 |
| 文件大?。?/td> | 332K |
| 代理商： | YS12S10-0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁
MCD10206 Rev. 1.0, 24-Jun-10
Page 8 of 27
www.power-one.com
YS12S10 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 10 A
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 to x.2 for maximum
temperature of 110 °C. Ambient temperature was
varied between 25 °C and 85 °C, with airflow rates
from 30 to 500 LFM (0.15 m/s to 2.5 m/s), and
vertical and horizontal converter mountings. The
airflow during the testing is parallel to the long axis of
the converter, going from pin 1 and pin 6 to pins 2–5.
For each set of conditions, the maximum load
current is defined as the lowest of:
(i) The output current at which any MOSFET
temperature
does
not
exceed
a
maximum
specified temperature (110 °C) as indicated by the
thermographic image, or
(ii) The maximum current rating of the converter
(10 A)
During normal operation, derating curves with
maximum FET temperature less than or equal to
110 °C should not be exceeded. Temperature on the
PCB at the thermocouple location shown in Fig. D
should not exceed 110 °C in order to operate inside
the derating curves.
Efficiency
Figure x.3 shows the efficiency vs. load current plot
for ambient temperature of 25 C, airflow rate of
200 LFM (1 m/s) and input voltages of 9.6 V, 12 V,
and 14 V.
Power Dissipation
Fig. x.4 shows the power dissipation vs. load current
plot for Ta = 25 C, airflow rate of 200 LFM (1 m/s)
with vertical mounting and input voltages of 9.6 V,
12 V, and 14 V.
Ripple and Noise
The output voltage ripple waveform is measured at
full rated load current. Note that all output voltage
waveforms are measured across a 1 μF ceramic
capacitor.
The output voltage ripple and input reflected ripple
current waveforms are obtained using the test setup
shown in Fig. E.
iS
Vout
Vsource
1
F
ceramic
capacitor
1
H
source
inductance
DC-DC
Converter
4x47
F
ceramic
capacitor
100
F
ceramic
capacitor
CO
CIN
Y-Series
Fig. E: Test setup for measuring input reflected-ripple currents,
is
and output voltage ripple.
相關PDF資料 |
PDF描述 |
|---|---|
| YS12S10-0G | DC-DC REG PWR SUPPLY MODULE |
| YS12S10-DG | DC-DC REG PWR SUPPLY MODULE |
| YS12S10-D | DC-DC REG PWR SUPPLY MODULE |
| YS12S16-0G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YS12S16-0 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| YS12S10-0G | 功能描述:DC/DC轉換器 0.7525-5.5Vout 10A 9.6-14VIn RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YS12S10-D | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YS12S10-DG | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YS12S16 | 制造商:Power-One 功能描述:DC-DC Converter, 9.6-14 VDC In., 0.7525-5.5 VDC Programmable @ 16 A, RoHS |
| YS12S16-0 | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。