- 您現在的位置：買賣IC網 > PDF目錄48109 > YS12S16-DG (POWER-ONE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | YS12S16-DG |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, ZMA-6 |
| 文件頁數： | 26/27頁 |
| 文件大?。?/td> | 407K |
| 代理商： | YS12S16-DG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁
OCT 18, 2006 revised to DEC 05, 2006
Page 8 of 27
www.power-one.com
YS12S16 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 16A
Ensuring components on the converter do not
exceed their ratings is important to maintaining high
reliability. If one anticipates operating the converter
at or close to the maximum loads specified in the
derating curves, it is prudent to check actual
operating
temperatures
in
the
application.
Thermographic
imaging
is
preferable;
if
this
capability is not available, then thermocouples may
be used. . It is recommended the use of AWG #40
gauge thermocouples to ensure measurement
accuracy. Careful routing of the thermocouple leads
will further minimize measurement error. Refer to
Fig. D for optimum measuring thermocouple
locations.
Fig. D: Location of the thermocouple for thermal testing
.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 for maximum temperature
of 120 °C. Ambient temperature was varied between
25 °C and 85 °C, with airflow rates from 30 to 500
LFM (0.15 m/s to 2.5 m/s), and vertical converter
mounting. The airflow during the testing is parallel to
the short axis of the converter, going from pin 1 and
pin 6 to pins 2 – 5.
For each set of conditions, the maximum load
current is defined as the lowest of:
(i) The output current at which any MOSFET
temperature does not exceed a maximum specified
temperature (120 °C) as indicated by the thermo-
graphic image, or
(ii) The maximum current rating of the converter
(16 A)
During normal operation, derating curves with
maximum FET temperature less than or equal to
120 °C should not be exceeded. Temperature on the
PCB at the thermocouple location shown in Fig. D
should not exceed 120 °C in order to operate inside
the derating curves.
Efficiency
Figure x.2 shows the efficiency vs. load current plot
for ambient temperature of 25 C, airflow rate of 200
LFM (1 m/s) and input voltages of 9.6 V, 12 V, and
14 V.
Power Dissipation
Fig. x.3 shows the power dissipation vs. load current
plot for Ta = 25 C, airflow rate of 200 LFM (1 m/s)
with vertical mounting and input voltages of 9.6 V,
12 V, and 14 V.
Ripple and Noise
The output voltage ripple waveform is measured at
full rated load current. Note that all output voltage
waveforms are measured across a 1
μF ceramic
capacitor.
The output voltage ripple and input reflected ripple
current waveforms are obtained using the test setup
shown in Fig. E.
iS
Vout
Vsource
1
μF
ceramic
capacitor
1
μH
source
inductance
DC/DC
Converter
4x47
μF
ceramic
capacitor
100
μF
ceramic
capacitor
CO
CIN
Y-Series
Fig. E: Test setup for measuring input reflected ripple
currents,
is and output voltage ripple.
相關PDF資料 |
PDF描述 |
|---|---|
| YS12S16-D | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YSF224B-D | DSP-DIGITAL FILTER, PDIP16 |
| YSF224B-M | DSP-DIGITAL FILTER, PDSO16 |
| YSF224B | SOUND ANALYSIS PROCESSOR |
| YSS205B-F | 8-BIT, 19 MHz, OTHER DSP, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| YS130101P14B | 制造商:n/a 功能描述:Power SCR |
| YS130101P18C | 制造商:n/a 功能描述:_ |
| YS130101UHP18C | 制造商:n/a 功能描述:_ |
| YS1363 | 功能描述:ANT YAGI 3ELEM 150MHZ 7.1DBD AG RoHS:是 類別:RF/IF 和 RFID >> RF 天線 系列:- 標準包裝:1 系列:* |
| YS150103AHP18C | 制造商:n/a 功能描述:Power SCR |
發布緊急采購，3分鐘左右您將得到回復。