參數資料
型號: Z0220516PSCR4292
廠商: ZILOG INC
元件分類: 調制器/解調器
英文描述: V2.22 Bis Modem Controller(V2.22Bis調制解調器控制器)
中文描述: 1.2 kbps DATA, MODEM-SUPPORT CIRCUIT, PDIP28
封裝: PLASTIC, DIP-28
文件頁數: 14/30頁
文件大?。?/td> 226K
代理商: Z0220516PSCR4292
Z02205
Modem Controller
ZiLOG
12
PS001000-MOD0599
D
Dial
The D command causes the modem to dial a telephone call according to the digits and
dial modifiers in the dial string following the command. Any commands following the
dial string on a command line are ignored, unless the semicolon dial modifier is the last
character in the dial string. If the modem is off-hook when the Dial command is given,
the modem dials immediately without trying to detect a dial tone. Characters other than
digits and dial modifiers in a dial string are ignored; however, they are counted as
characters in the command line buffer.
If line current sensing is enabled, and line current is detected before the modem is taken
OFF-HOOK when the modem dials, a NO CARRIER result code is displayed and the
modem enters the IDLE state. If the modem needs not dial (that is, ATD with no dial
string), the modem assumes the call was manually established and attempts to make a
connection.
The D command is not valid when the modem is in the On-Line state.
See “Dial Modifiers and “Modem Result Codes for more information.
&D determines how the modem responds to the DTR signal from the terminal. The
country configuration may prevent the modem from detecting terminal DTR. In this
case, the modem assumes DTR is always on. In North America, terminal DTR is
normally detected. If DTR detection has been prevented, the modem will respond with
an ERROR result to this command.
The response to changes in DTR also depends on the &Q and &D commands. This table
defines what happens when DTR goes off for all possible combinations of the &D and
&Q commands. To see what happens when DTR goes on, refer to the &Q command. The
default value is &D0 in North America:
&D0 &D1 &D2 &D3
&Q0
None B C D
&Q1
A B C D
A
The modem hangs up the telephone line and issues an OK result code.
B
If in the On-Line state, the modem goes into the Command state, and issues
an OK result code.
C
The modem hangs up the telephone line and issues an OK result code.
Auto-Answer is disabled as long as DTR stays off.
D
The modem resets.
&D
Data Terminal Ready
Options
Table 2. AT Command Set (Continued)
Command
Function and Description
相關PDF資料
PDF描述
Z0220516SSC1961 V2.22 Bis Modem Controller(V2.22Bis調制解調器控制器)
Z0220516SSCR4259 V2.22Bis Modem Controller(V2.22Bis調制解調器控制器)
Z0220516SSCR4292 Low Power Modem Controller(低功耗單片調制解調器控制器)
Z02205 Modem Controller(低功耗單片modem)
Z02215 Synchronous Single-chip V.22bis Modem(同步單片V.22Bis調制解調器)
相關代理商/技術參數
參數描述
Z0220516PSG1961 功能描述:電信線路管理 IC OTP CONTROLLER 86E34 RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
Z0220516PSGR3641 功能描述:電信線路管理 IC OTP CONTROLLER 86E34 RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
Z0220516SSC 功能描述:電信線路管理 IC TP CONTROLLER 86E34 RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
Z0220516SSC1961 功能描述:電信線路管理 IC OTP CONTROLLER 86E34 RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
Z0220516SSC1961TR 功能描述:IC MODEM CTRL 28SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21,V.22,V.23,V.29,V.32,V.34,V.90,V.92,Bell 103,Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574