- 您現在的位置：買賣IC網 > PDF目錄373752 > Z0220516SSC1961 (ZILOG INC) V2.22 Bis Modem Controller(V2.22Bis調制解調器控制器) PDF資料下載
參數資料
| 型號： | Z0220516SSC1961 |
| 廠商： | ZILOG INC |
| 元件分類： | 調制器/解調器 |
| 英文描述： | V2.22 Bis Modem Controller(V2.22Bis調制解調器控制器) |
| 中文描述： | 1.2 kbps DATA, MODEM-SUPPORT CIRCUIT, PDSO28 |
| 封裝： | SOIC-28 |
| 文件頁數： | 24/30頁 |
| 文件大?。?/td> | 226K |
| 代理商： | Z0220516SSC1961 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Z02205
Modem Controller
ZiLOG
22
PS001000-MOD0599
ESCAPE SEQUENCES
An escape sequence is defined as one or more particular
characters sent from the terminal to the modem during the
On-Line state. This sequence is activated to switch the mo-
dem to the command state so modem commands may be en-
tered during a telephone line connection. The Escape Se-
quence characters are typically sent to the other modem as
data.
An escape sequence should not occur accidentally during
an exchange of data between two modems. Unfortunately,
it is impossible to guarantee that any escape sequence will
never occur naturally, because there are no restrictions on
the data or timing between characters sent between two mo-
dems during the On-Line state.
The only method of switching from the On-Line state to the
Command state that never occurs naturally during an ex-
change of data is the Data Terminal Ready signal (the &D1
command). The terminal has complete control of this signal
and it is not part of the data exchanged between the modems.
The Hayes Escape Sequence was adopted by many modem
manufacturers and communication programs before Hayes
was granted a patent for the escape sequence guard times.
Now the unpatented
TIME INDEPENDENT ESCAPE SE-
QUENCE
(
TIES
) has gained popularity with many modem
manufacturers.
TIES Escape Sequence
TIES
was developed by a number of modem manufacturers
in response to Hayes enforcing patent rights for their escape
sequence guard time patent.
The Time Independent Escape Sequence, is a sequence of
3 escape characters (+ characters by default). When these
characters are recognized, the modem enters the
COM-
MAND
state without sending a confirming result code to the
terminal. The modem then starts a prompt delay timer. From
that point:
If one of the recognized AT commands is received be-
fore the timer expires, the timer is stopped, the command
is executed, and its result code is sent to the terminal.
If any other data is received while the timer is running,
the timer is stopped, the modem returns to the On-Line
state, and the received data is sent to the other modem.
If the timer expires, a confirming result code is sent to
the terminal, indicating the modem is in the Command
state.
The escape character and prompt delay timer can be
changed by writing new values to S-registers S2 and S12.
CARRIER DETECTION
After Handshaking, the modem determines if a telephone
line connection exists by detecting the carrier signal from
the other modem. If the carrier is not detected for a long
enough period of time, the modem assumes the telephone
line connection with the other modem has been broken. The
modem uses S-register
S9
to determine how long a carrier
must be present before it is
detected
. The modem uses S-
register
S10
to determine how long a carrier is not detected
before the telephone line is hung up.
BLACKLISTING MANAGEMENT
Blacklisting applies separately to each number dialed, and
indicates the call blocking capability for specific phone
numbers. To save Z02205 RAM, calls are treated as if they
are all to the same number.
The first connection attempt after modem reset or a suc-
cessful connection is always allowed. If a connection at-
tempt is not successful, then each following connection
attempt is checked as follows:
1. If voice answer was detected too many times the
attempt is not allowed,
Modem Result Code
indicates
the call is BLACKLISTED.
2. If the attempt occurred too quickly (within the inter-
call timing period) then the attempt is not allowed,
Modem Result Code
indicates the call is DELAYED.
3. If there is a blacklisting period limiting the number of
attempts that may be made within the period, and too
many attempts have been made, then the attempt is not
allowed,
Modem Result Code
indicates the call is
either DELAYED (if a call may be made later), or
BLACKLISTED (if no call may be made later).
相關PDF資料 |
PDF描述 |
|---|---|
| Z0220516SSCR4259 | V2.22Bis Modem Controller(V2.22Bis調制解調器控制器) |
| Z0220516SSCR4292 | Low Power Modem Controller(低功耗單片調制解調器控制器) |
| Z02205 | Modem Controller(低功耗單片modem) |
| Z02215 | Synchronous Single-chip V.22bis Modem(同步單片V.22Bis調制解調器) |
| Z02922 | Synchronous Single-chip Modem(同步單片調制解調器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Z0220516SSC1961TR | 功能描述:IC MODEM CTRL 28SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| Z0220516SSCR3641 | 功能描述:電信線路管理 IC OTP CONTROLLER 86E34 RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| Z0220516SSCR3641T | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:MODEM CONTROLLER IDEAL FOR LOW POWER CONSUMPTION, SMALL SIZE REQUIREMENTS |
| Z0220516SSCR3641TR | 功能描述:IC MODEM CTRL 28SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:- 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| Z0220516SSCR4259 | 功能描述:電信線路管理 IC OTP CONTROLLER 86E34 RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。