參數資料
型號: Z53C80
廠商: ZiLOG, Inc.
英文描述: SMALL COMPUTER SYSTEM INTERFACE (SCSI)
中文描述: 小型計算機系統接口(SCSI)
文件頁數: 7/40頁
文件大?。?/td> 447K
代理商: Z53C80
7
Z53C80 SCSI
Z
ILOG
PS97SCC0200
FUNCTIONAL DESCRIPTION
General.
The Small Computer System interface (SCSI)
device has a set of eight registers that are controlled by the
CPU. By reading and writing the appropriate registers, the
CPU may initiate any SCSI Bus activity or may sample and
assert any signal on the SCSI Bus. This allows the user to
implement all or any of the SCSI protocol in software. These
registers are read (written) by activating /CS with an
address on A2-A0 and then issuing a /RD (/WR) pulse. This
section describes the operation of the internal registers
(Table 1).
Table 1. Register Summary
Address
A2
A1
A0
R/W
Register Name
0
0
0
0
0
0
0
0
1
R
W
R/W
Current SCSI Data
Output Data
Initiator Command
0
0
1
1
1
0
0
1
0
R/W
R/W
R
Mode
Target Command
Current SCSI Bus Status
1
1
1
0
0
0
0
1
1
W
R
W
Select Enable
Bus and Status
Start DMA Send
1
1
1
1
1
1
1
1
0
0
1
1
R
W
R
W
Input Data
Start DMA Target Receive
Reset Parity/Interrupt
Start DMA Initiator Receive
Data Registers.
The data registers are used to transfer
SCSI commands, data, status, and message bytes between
the microprocessor Data Bus and the SCSI Bus. The SCSI
does not interpret any information that passes through the
data registers. The data registers consist of the transparent
Current SCSI Data Register, the Output Data Register, and
the Input Data Register.
Current SCSI Data Register.
Address 0(Read Only). The
Current SCSI Data Register (Figure 5) is a read-only
register which allows the microprocessor to read the active
SCSI Data Bus. This is accomplished by activating /CS
with an address on A2-A0 and issuing a /RD pulse. If parity
checking is enabled, the SCSI Bus parity is checked at the
beginning of the read cycle. This register is used during a
programmed I/O data read or during Arbitration to check
for higher priority arbitrating devices. Parity is not
guaranteed valid during Arbitration.
Figure 5. Current SCSI Data Register
Output Data Register.
Address 0(Write Only). The Output
Data Register (Figure 6) is a write-only register that is used
to send data to the SCSI Bus. This is accomplished by
either using a normal CPU write, or under DMA control, by
using /WR and /DACK. This register also asserts the
proper ID bits on the SCSI Bus during the Arbitration and
Selection phases.
/DB0
/DB1
/DB2
/DB3
/DB4
/DB5
/DB6
/DB7
Address: 0
(Read Only)
D7 D6 D5 D4 D3 D2 D1 D0
/DB0
/DB1
/DB2
/DB3
/DB4
/DB5
/DB6
/DB7
D7 D6 D5 D4 D3 D2 D1 D0
Address: 0
(Write Only)
Figure 6. Output Data Register
相關PDF資料
PDF描述
Z53C8003PSC SMALL COMPUTER SYSTEM INTERFACE (SCSI)
Z53C8003VSC SMALL COMPUTER SYSTEM INTERFACE (SCSI)
Z53C80SCSI SMALL COMPUTER SYSTEM INTERFACE (SCSI)
Z54122 RETRIGGERABLE MONOSTABLE MULTIVIBRATOR
Z5U0603 ceramic chip capacitors
相關代理商/技術參數
參數描述
Z53C8003ASG 功能描述:SCSI 接口集成電路 3 MB/SEC CMOS SCSI 1 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube
Z53C8003FSC 功能描述:SCSI 接口集成電路 3MB/SEC CMOS SCSI 1 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube
Z53C8003FSC00TR 功能描述:IC 3 MB/SEC CMOS SCSI 1 48-QFP RoHS:否 類別:集成電路 (IC) >> 接口 - 信號終端器 系列:Z53C80 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:SCSI,SE 端子數:9 電源電壓:4 V ~ 5.25 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC(0.154",3.90mm 寬) 供應商設備封裝:16-SOIC 包裝:管件
Z53C8003FSG 功能描述:SCSI 接口集成電路 3MB/SEC CMOS SCSI 1 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube
Z53C8003PSC 功能描述:SCSI 接口集成電路 3MB/SEC CMOS SCSI I RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube