參數資料
型號： Z8613012PSC
廠商： ZILOG INC
元件分類： 消費家電
英文描述： CAP 2200PF 100V 10% X7R AXIAL TR-14
中文描述： SPECIALTY CONSUMER CIRCUIT, PDIP18
封裝： PLASTIC, DIP-18
文件頁數： 6/50頁
文件大?。?/td> 927K
代理商： Z8613012PSC
Z86129/130/131
NTSC Line 21 Decoder
P R E L I M I N A R Y
6
DS96TEL0200
PIN DESCRIPTIONS
Inputs
VIDEO (Pin 7).
Composite NTSC video input, 1.0V p-p
(nom), band limited to 600 kHz. Circuit will operate with
signal variation between 0.7-1.4V p-p. The polarity is sync
tips negative. This signal pin should be AC coupled
through a 0.1
μ
F capacitor and driven by a source
impedance of 470 ohms or less.
HIN (Pin 5).
Horizontal sync input at CMOS levels. When
the device is used in the VIDEO LOCK mode, this signal
pulls the on-chip VCO within the proper range. The circuit
uses the frequency of this signal which must be within
±
3%
Fh but can be of either polarity. When used in the H LOCK
mode, the VCO phase locks to the rising edge of this
signal. The HPOL bit of the H Position register can be set
to operate with either polarity of input signal. This is usually
the H Flyback signal. The timing difference between HIN
rising edge and the leading edge of composite sync (of
VIDEO input) is one of the factors which will affect the
horizontal position of the display. Any shift resulting from
the timing of this signal can be compensated for with the
horizontal timing value in H Position Register.
SMS (Pin 6).
Mode select pin for the Serial Control Port.
When this input is at a CMOS High state (1) the Serial
Control Port will operate in the SPI mode. When the input
is Low (0), the Serial Control Port will operate in the I
2
C
slave mode. In SPI mode, the SEN pin must be tied High.
(See Reset Operation section.)
SEN (Pin 4).
Enable signal for the SPI mode operation of
the Serial Control Port. When this pin is Low (0), the SPI
port is disabled and the SDO pin is in the high-impedance
state. Transitions on the SCK and SDA pins are ignored.
SPI mode operation is enabled when SMS is High (1).
SCK (Pin 15).
Input pin for serial clock signal from the
master control device. In I
2
C mode operation the clock rate
is expected to be within I
2
C limits. In SPI mode, the
maximum clock frequency is 10 MHz.
Reset Operation.
When the SMS and SEN pins are both
in the Low (0) state, the part will be in the Reset state.
Therefore, in the I
2
C mode the SEN pin can be used as an
NReset input. When SPI mode is used, if three wire
operation is desired, both SMS and SEN can be tied
together and used as the NReset input. In either mode,
NReset must be held Low (0) for at least 100 ns.
Input/Output
VIN/INTRO (Pin 13).
In external (EXT) vertical lock mode
of operation, the internal vertical sync circuits will lock to
the VIN input signal applied at this pin. The part will lock to
the rising or falling edge of the signal in accordance with
the setting of the V Polarity command. The default is rising
edge. The VIN pulse must be at least 2 lines wide.
In INTRO Mode, when configured for internal vertical
synchronization, this pin will be an output pin providing an
interrupt signal to the master control device in accordance
with the settings in the Interrupt Mask Register.
SDA (Pin 14).
When the Serial Control Port has been set
to I
2
C mode operation, this pin serves as the bidirectional
data line for sending and receiving serial data. In SPI mode
operation it operates as serial data input. SPI mode output
data is available on the SDO pin.
Outputs
SDO (Pin 16).
Provides the serial data output when SPI
mode communications have been selected. This pin is not
used in I
2
C mode operation.
Box (Pin 17*).
Black box keying output is an active High,
CMOS level signal used to key in the black box in the
captions/text displays. This output will be in the high-
impedance state when the background attribute has been
set to semi-transparent (*Z86129 only).
RED, GREEN, BLUE (Pins 2*, 3*, 18*).
Positive acting
CMOS levels signals (*Z86129 only).
Color Mode: Red, Green and Blue character video outputs
for use in a color receiver.
I
Mono Mode: All three outputs carry the character
luminance information.
Notes:
The selection of Color/Mono Mode is user
controlled in bit D
1
of the Configuration Register
(Address=00h). (See Internal Registers section.).
相關PDF資料
PDF描述
Z8613012SSC CAP 2400PF 100V 10% X7R AXIAL TR-14
Z8613112PSC Ceramic Multilayer Capacitor; Capacitor Type:General Purpose; Capacitance:0.1uF; Capacitance Tolerance: 10%; Voltage Rating:100VDC; Capacitor Dielectric Material:Multilayer Ceramic; Termination:Axial Leaded RoHS Compliant: Yes
Z8613112SSC CAP 0.056UF 100V 10% X7R AXIAL TR-14
Z86160 SET-TOP CONTROLLER
Z86193 CMOS Z8 MICROCONTROLLER MULTIPLIER/DIVIDER/SEARCH/MERGE
相關代理商/技術參數
參數描述
Z8613012PSG 功能描述:編碼器、解碼器、復用器和解復用器 V CHIP&TIME OF DAY RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
Z8613012SSC 功能描述:編碼器、解碼器、復用器和解復用器 V CHIP&TIME OF DAY RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
Z8613012SSC00TR 功能描述:IC TIME OF DAY SMART V 18SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 編碼器，解碼器，轉換器 系列:- 產品變化通告:Development Systems Discontinuation 26/Apr/2011 標準包裝:1 系列:- 類型:編碼器 應用:DVB-S.2 系統 電壓 - 電源，模擬:- 電壓 - 電源，數字:- 安裝類型:- 封裝/外殼:模塊 供應商設備封裝:模塊 包裝:散裝 其它名稱:Q4645799
Z8613012SSG 功能描述:編碼器、解碼器、復用器和解復用器 V CHIP&TIME OF DAY RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
Z8613012SSG00TR 制造商:Zilog Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*