參數資料
型號： Z86C08
廠商： ZiLOG, Inc.
英文描述： CMOS 8-BIT LOW-COST 1K/2K-ROM MICROCONTROLLERS
中文描述： 的CMOS 8位的低費用1K/2K-ROM微控制器
文件頁數： 26/34頁
文件大?。?/td> 207K
代理商： Z86C08
Z86C04/C08
CMOS 8-Bit Low-Cost 1K/2K-ROM Microcontrollers
Zilog
26
P R E L I M I N A R Y
DS97DZ80502
Clock.
The on-chip oscillator has a high-gain, parallel-res-
onant amplifier for connection to a RC, crystal, ceramic
resonator, LC, or any suitable external clock source
(XTAL1 = Input, XTAL2 = Output). The crystal should be
AT cut, 12 MHz max, with a series resistance (RS) less
than or equal to 100 Ohms.
The crystal should be connected across XTAL1 and
XTAL2 using the vendor’s crystal recommended capaci-
tors (which depends on the crystal manufacturer, ceramic
resonator and PCB layout) from each pin directly to device
Ground pin 14 (Figure 16).
Note that the crystal capacitor loads should be connected
to V
SS
pin 14 to reduce ground noise injection.
To use 32 KHz crystal, the 32 KHz operational mask option
must be selected, and an external resistor R must be con-
nected across XTAL1 and XTAL2.To use RC oscillator,
the RC oscillator option must be selected.
HALT Mode.
This instruction turns off the internal CPU
clock but not the crystal oscillation. The counter/timers and
external interrupts IRQ0, IRQ1, IRQ2, and IRQ3 remain
active. The device can be recovered by interrupts, either
externally or internally generated. An interrupt request
must be executed (enabled) to exit HALT mode. After the
interrupt service routine, the program continues from the
instruction after the HALT.
STOP Mode.
This instruction turns off the internal clock
and external crystal oscillation and reduces the standby
current. The STOP mode can be released by two methods.
The first method is a RESET of the device by removing
V
CC
or dropping the V
CC
below V
LV
. The second method
is if P27 is at a low level when the device executes the
STOP instruction. A low condition on P27 releases the
STOP mode regardless if configured for input or output.
Program execution under both conditions begins at loca-
tion 000C (Hex). However, when P27 is used to release
the STOP mode, the I/O port mode registers are not re-
configured to their default power-on conditions. This pre-
vents any I/O, configured as output when the STOP in-
struction was executed, from glitching to an unknown
state. To use the P27 release approach with STOP mode,
use the following instruction:
Note:
(X = dependent upon user’s application.)
In order to enter STOP or HALT mode, it is necessary to
first flush the instruction pipeline to avoid suspending exe-
cution in mid-instruction. To do this, the user must execute
a NOP (opcode = FFH) immediately before the appropriate
sleep instruction, that is, as follows:
Watch-Dog Timer (WDT).
The Watch-Dog Timer is en-
abled by instruction WDT. When the WDT is enabled, it
cannot be stopped by the instruction. With the WDT in-
struction, the WDT should be refreshed once the WDT is
enabled within every Twdt period; otherwise, the Z8 resets
itself. The WDT instruction affects the Flags accordingly: Z
= 1, S = 0, V = 0.
WDT = 5F (Hex)
LD
NOP
STOP
P2M, #1XXX XXXXB
FF
6F
NOP
STOP
; clear the pipeline
; enter STOP mode
or
FF
7F
NOP
HALT
; clear the pipeline
; enter HALT mode
Figure 15. Oscillator Configuration
XTAL1
XTAL2
C1
C2
*
C1
*
C2
*
Ceramic
Resonator
or Crystal
External Clock
L
LC Clock
XTAL1
XTAL2
XTAL1
XTAL2
*
*
= Use pin 14.
XTAL1
XTAL2
C1
C2
R
32 KHz
32 KHz Crystal Clock
XTAL1
XTAL2
R
RC Clock
C
*
*
*
相關PDF資料
PDF描述
Z86C04 CMOS 8-BIT LOW-COST 1K/2K-ROM MICROCONTROLLERS
Z86C15 CMOS Z8 8-BIT MCU KEYBOARDCONTROLLER
Z86C33 .068UF/400VDC METAL POLY CAP
Z86C43 CMOS Z8 CONSUMER CONTROLLER PROCESSOR
Z86C34 CMOS Z8 MCU(CMOS Z8系列微控制器)
相關代理商/技術參數
參數描述
Z86C08-08PEC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
Z86C08-08PSC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
Z86C0812PECRXXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|Z8 CPU|CMOS|DIP|18PIN|PLASTIC
Z86C0812PSCR2611 制造商:Zilog Inc 功能描述:
Z86C0812PSCR507A 制造商:Zilog Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*