- 您現在的位置：買賣IC網 > PDF目錄373767 > Z86E40 (ZiLOG, Inc.) Z8 4K OTP Microcontroller( Z8系列4k ROM一次可編程微控制器) PDF資料下載
參數資料
| 型號： | Z86E40 |
| 廠商： | ZiLOG, Inc. |
| 英文描述： | Z8 4K OTP Microcontroller( Z8系列4k ROM一次可編程微控制器) |
| 中文描述： | Z8 4K的檢察官辦公室的微控制器（Z8系列4K的ROM的一次可編程微控制器） |
| 文件頁數： | 24/64頁 |
| 文件大?。?/td> | 391K |
| 代理商： | Z86E40 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
Z86E30/E31/E40
Z8 4K OTP Microcontroller
Zilog
24
P R E L I M I N A R Y
DS97Z8X0502
PIN FUNCTIONS
EPROM Programming Mode
D7–D0
Data Bus. The data can be read from or written to
external memory through the data bus.
A11–A0
Address Bus. During programming, the EPROM
address is written to the address bus.
V
CC
Power Supply. This pin must supply 5V during the
EPROM read mode and 6V during other modes.
CE
Chip Enable (active Low). This pin is active during
EPROM Read Mode, Program Mode, and Program Verify
Mode.
OE
Output Enable (active Low). This pin drives the direc-
tion of the Data Bus. When this pin is Low, the Data Bus is
output, when High, the Data Bus is input.
EPM
EPROM Program Mode. This pin controls the differ-
ent EPROM Program Mode by applying different voltages.
V
PP
Program Voltage. This pin supplies the program volt-
age.
PGM
Program Mode (active Low). When this pin is Low,
the data is programmed to the EPROM through the Data
Bus.
Application Precaution
The production test-mode environment may be enabled
accidentally during normal operation if excessive noise
surges above V
CC
occur on pins XTAL1 and RESET.
In addition, processor operation of Z8 OTP devices may be
affected by excessive noise surges on the V
PP
, CE, EPM,
OE pins while the microcontroller is in Standard Mode.
Recommendations for dampening voltage surges in both
test and OTP mode include the following:
I
Using a clamping diode to V
CC
I
Adding a capacitor to the affected pin
Standard Mode
XTAL
Crystal 1 (time-based input). This pin connects a
parallel-resonant crystal, ceramic resonator, LC, RC net-
work, or external single-phase clock to the on-chip oscilla-
tor input.
XTAL2
Crystal 2 (time-based output). This pin connects a
parallel-resonant crystal, ceramic resonator, LC, or RC
network to the on-chip oscillator output.
R/W
Read/Write (output, write Low). The R/W signal is
Low when the CCP is writing to the external program or
data memory (Z86E40 only).
RESET
Reset (input, active Low). Reset will initialize the
MCU. Reset is accomplished either through Power-On,
Watch-Dog Timer reset, STOP-Mode Recovery, or exter-
nal reset. During Power-On Reset and Watch-Dog Timer
Reset, the internally generated reset drives the reset pin
low for the POR time. Any devices driving the reset line
must be open-drain in order to avoid damage from a pos-
sible conflict during reset conditions. Pull-up is provided in-
ternally. After the POR time, RESET is a Schmitt-triggered
input.
To avoid asynchronous and noisy reset problems, the
Z86E40 is equipped with a reset filter of four external
clocks (4TpC). If the external reset signal is less than 4TpC
in duration, no reset occurs. On the fifth clock after the re-
set is detected, an internal RST signal is latched and held
for an internal register count of 18 external clocks, or for
the duration of the external reset, whichever is longer. Dur-
ing the reset cycle, DS is held active Low while AS cycles
at a rate of TpC/2. Program execution begins at location
000CH, 5–10 TpC cycles after RESET is released. For
Power-On Reset, the reset output time is 5 ms. The
Z86E40 does not reset WDTMR, SMR, P2M, and P3M
registers on a STOP-Mode Recovery operation.
ROMless
(input, active Low). This pin, when connected to
GND, disables the internal ROM and forces the device to
function as a Z86C90/C89 ROMless Z8. (Note that, when
left unconnected or pulled High to V
CC
, the device func-
tions normally as a Z8 ROM version).
Note:
When using in ROM Mode in High EMI (noisy) envi-
ronment, the ROMless pins should be connected directly
to V
CC
.
相關PDF資料 |
PDF描述 |
|---|---|
| Z86E4700ZDP | CMOS Z8 8BIT MICROCONTROLLER |
| Z86E47 | CMOS Z8 8BIT MICROCONTROLLER |
| Z86E72 | OTP IR Microcontroller(一次可編程紅外線微控制器) |
| Z86E73 | OTP IR Microcontroller(一次可編程紅外線微控制器) |
| Z86K14 | CMOS Z8 8-Bit MCU Keyboard Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Z86E4000ZDV | 功能描述:44 PIN PLCC ADAPTER RoHS:否 類別:編程器，開發系統 >> 適配器 系列:- 標準包裝:96 系列:- 模塊/板類型:TQFP 插座模塊 適用于相關產品:- |
| Z86E4001ZDF | 功能描述:8位微控制器 -MCU Z8 OTP Conv(QFP) Kit RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| Z86E4001ZDV | 功能描述:8位微控制器 -MCU Z8 OTP Con(PLCC) Kit RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| Z86E4012PSC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-8-BIT MCU-OTP |
| Z86E4012VSC | 制造商:Zilog Inc 功能描述:MicroController, 8-Bit, 44 Pin, Plastic, PLCC |
發布緊急采購，3分鐘左右您將得到回復。