參數資料
型號： Z86E61
廠商： ZiLOG, Inc.
英文描述： CMOS Z8 16K/32K EPROM MICROCONTROLLER
中文描述： Z8 16K/32K的CMOS存儲器單片機
文件頁數： 7/44頁
文件大小： 466K
代理商： Z86E61
7
Z86E61/E63 Z8
MCU
WITH
16K/32K EPROM
P R E L I M I N A R Y
PIN FUNCTIONS
ROMless
(input, active Low). Connecting this pin to GND
disables the internal ROM and forces the device to func-
tion as a Z86C91 ROMless Z8 (see the Z86C91 product
specification for more information). When left unconnected
or pulled High to V
, the device functions as a normal
Z86E61/E63 EPROM version.
Note:
This pin is only avail-
able on the 44-pin versions of the Z86E61/E63.
/DS
(output, active Low). Data Strobe is activated once for
each external memory transfer. For a READ operation,
data must be available prior to the trailing edge of /DS. For
WRITE operations, the falling edge of /DS indicates that
output data is valid.
/AS
(output, active Low). Address Strobe is pulsed once at
the beginning of each machine cycle. Address output is
through Port 1 for all external programs. Memory address
transfers are valid at the trailing edge of /AS. Under
program control, /AS can be placed in the high-
impedance state along with Ports 0 and 1, Data Strobe,
and Read/Write.
XTAL2, XTAL1
Crystal 2, Crystal 1(time-based input and
output, respectively). These pins connect a parallel-
resonant crystal, ceramic resonator, LC, or any external
single-phase clock to the on-chip oscillator and buffer.
R//W
(output, write Low). The Read/Write signal is Low
when the MCU is writing to the external program or data
memory.
/RESET
(input, active Low). To avoid asynchronous and
noisy reset problems, the Z86E61/E63 is equipped with a
reset filter of four external clocks (4TpC). If the external
/RESET signal is less than 4TpC in duration, no reset
occurs.
On the fifth clock after the /RESET is detected, an internal
RST signal is latched and held for an internal register count
of 18 external clocks, or for the duration of the external
/RESET, whichever is longer. During the reset cycle, /DS is
held active Low while /AS cycles at a rate of TpC/2. When
/RESET is deactivated, program execution begins at loca-
tion 000C (HEX). Power-up reset time must be held low for
50 ms, or until V
CC
is stable, whichever is longer.
Port 0
(P07-P00
).
Port 0 is an 8-bit, nibble programmable,
bidirectional, TTL compatible port. These eight I/O lines
can be configured under software control as a nibble I/O
port, or as an address port for interfacing external memory.
When used as an I/O port, Port 0 may be placed under
handshake control. In this configuration, Port 3, lines P32
and P35 are used as the handshake control /DAV0 and
RDY0 (Data Available and Ready). Handshake signal
assignment is dictated by the I/O direction of the upper
nibble P07-P04. The lower nibble must have the same
direction as the upper nibble to be under handshake
control.
For external memory references, Port 0 can provide ad-
dress bits A11-A8 (lower nibble) or A15-A8 (lower and
upper nibbles) depending on the required address space.
If the address range requires 12 bits or less, the upper
nibble of Port 0 can be programmed independently as I/O
while the lower nibble is used for addressing. If one or both
nibbles are needed for I/O operation, they must be config-
ured by writing to the Port 0 Mode register.
In ROMless mode, after a hardware reset, Port 0 lines are
defined as address lines A15-A8, and extended timing is
set to accommodate slow memory access. The initializa-
tion routine can include reconfiguration to eliminate this
extended timing mode (Figure 8).
Port 1
(P17-P10)
.
Port 1 is an 8-bit, byte programmable,
bidirectional, TTL compatible port. It has multiplexed Ad-
dress (A7-A0) and Data (D7-D0) ports. For Z86E61/E63,
these eight I/O lines can be programmed as input or output
lines or are configured under software control as an
address/data port for interfacing external memory. When
used as an I/O port, Port 1 can be placed under handshake
control. In this configuration, Port 3 lines, P33 and P34, are
used as the handshake controls RDY1 and /DAV1.
Memory locations greater than 16384 (E61) or 32768 (E63)
are referenced through Port 1. To interface external memory,
Port 1 must be programmed for the multiplexed Address/
Data mode. If more than 256 external locations are re-
quired, Port 0 must output the additional lines.
Port 1 can be placed in high-impedance state along with
Port 0, /AS, /DS, and R//W, allowing the MCU to share
common resources in multiprocessor and DMA applica-
tions. Data transfers are controlled by assigning P33 as a
Bus Acknowledge input, and P34 as a Bus Request output
(Figure 9).
相關PDF資料
PDF描述
Z86E64 CMOS Z8 OTP Microcontroller
Z86L70 IR/Low-Voltage Microcontroller
Z86L71 IR/Low-Voltage Microcontroller
Z86L75 IR/Low-Voltage Microcontroller
Z86C71 IR/Low-Voltage Microcontroller
相關代理商/技術參數
參數描述
Z86E6116ASG 功能描述:8位微控制器 -MCU Z8 16K OTP 16 MHZ WITH UART RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
Z86E6116FSC 功能描述:8位微控制器 -MCU 16K OTP 16MHzW/UART RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
Z86E6116FSC00TR 功能描述:IC Z8 MCU OTP 16K 44PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:Z8® 產品培訓模塊:The Ultra-Low Power MSP430 MSP430 Overview MSP430 Design Tools MSP430 Peripherals MSP430x2xx/4xx and Wireless Overview Portable Medical Solutions with MSP430 MSP430 for Utility Metering Solutions MSP430: How to JTAG MSP430, How To Use the Clock System Grace Software Graphical User Interface MCU Overview Driver Library MSP430Ware Overview 標準包裝:1 系列:MSP430x4xx 核心處理器:RISC 芯體尺寸:16-位 速度:8MHz 連通性:SPI，UART/USART 外圍設備:欠壓檢測/復位，LCD，POR，PWM，WDT 輸入/輸出數:48 程序存儲器容量:32KB（32K x 8 + 256B） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:100-LQFP 包裝:Digi-Reel® 其它名稱:296-26232-6
Z86E6116FSG 功能描述:8位微控制器 -MCU 16K OTP 16MHzW/UART RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
Z86E6116PSC 功能描述:8位微控制器 -MCU 16K OTP 16MHz W/UART RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*