- 您現在的位置：買賣IC網 > PDF目錄382791 > μPD78P4038 (NEC Corp.) 8/16 Bit Single Chip Microcontrollers(8/16位單片微控制器) PDF資料下載
參數資料
| 型號： | μPD78P4038 |
| 廠商： | NEC Corp. |
| 英文描述： | 8/16 Bit Single Chip Microcontrollers(8/16位單片微控制器) |
| 中文描述： | 8 / 16位單片機微控制器（8 / 16位單片微控制器） |
| 文件頁數： | 22/72頁 |
| 文件大?。?/td> | 325K |
| 代理商： | ΜPD78P4038 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
μ
PD78P4038
22
(1) Read mode
Set CE to L and OE to L to set read mode.
(2) Output disable mode
Set OE to H to set high impedance for data output and output disable mode.
Consequently, if several
μ
PD78P4038 devices are connected to a data bus, the OE pins can be controlled to
select data output from any of the devices.
(3) Standby mode
Set CE to H to set standby mode.
In this mode, data output is set to high impedance regardless of the OE setting.
(4) Page data latch mode
At the beginning of page write mode, set CE to H, PGM to H, and OE to L to set page data latch mode.
In this mode, 1 page (4 bytes) of data are latched to the internal address/data latch circuit.
(5) Page write mode
After latching the address and data for one page (4 bytes) using page data latch mode, adding a 0.1-ms program
pulse (active, low) to the PGM pin with both CE and OE set to H causes page write to be executed. Later, setting
both CE and OE to L causes program verification to be executed.
If programming is not completed after one program pulse, the write and verify operations may be repeated X times
(where X
≤
10).
(6) Byte write mode
Adding a 0.1-ms program pulse (active, low) to the PGM pin with both CE and OE set to H causes byte write
to be executed. Later, setting OE to L causes program verification to be executed.
If programming is not completed after one program pulse, the write and verify operations may be repeated X times
(where X
≤
10).
(7) Program verify mode
Set CE to L, PGM to H, and OE to L to set program verify mode. Use verify mode for verification following each
write operation.
(8) Program inhibit mode
Program inhibit mode is used to write to a single device when several
μ
PD78P4038 devices are connected in
parallel to OE , V
PP
, and D0 to D7 pins.
Use the page write mode or byte write mode described above for each write operation. Write operations cannot
be done for devices in which the PGM pin has been set to H.
相關PDF資料 |
PDF描述 |
|---|---|
| μPD78P9014 | 8 Bit Single Chip Microcontrollers(8位單片微控制器) |
| μPD98401A | ATM SAR Chip(高性能異步傳輸模式控制器) |
| μPDPD30101 | 64-Bit Micro[rocessor(64位微處理器) |
| μPG2106TB | L-Band PA Driver Amplifier(L波段PA驅動器放大器) |
| μPG2110TB | L-Band PA Driver Amplifier(L波段PA驅動器放大器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PD7935 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:FOR OPTICAL COMMUNICATION |
| PD7937 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:InGaAs PIN PHOTO DIODES |
| PD793D26 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:InGaAs PIN PHOTO DIODES |
| PD793D7 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:InGaAs PIN PHOTO DIODES |
| PD79920-0M | 制造商:Citizen Systems America Corporation 功能描述:Mobile Printer - PD24 USB Cable |
發布緊急采購，3分鐘左右您將得到回復。