- 您現在的位置：買賣IC網 > PDF目錄24745 > 0603LGCT (赫備國際貿易（上海）有限公司) SURFACE MOUNT DEVICE LED PDF資料下載
參數資料
| 型號： | 0603LGCT |
| 廠商： | 赫備國際貿易（上海）有限公司 |
| 英文描述： | SURFACE MOUNT DEVICE LED |
| 中文描述： | 表面貼裝器件的LED |
| 文件頁數： | 9/10頁 |
| 文件大小： | 791K |
| 代理商： | 0603LGCT |
SURFACE MOUNT DEVICE LED
Part No. :
0603LGCT
REV:A / 01
Bin Code List
Luminous Intensity(IV), Unit:mcd@20mA
Forward Voltage(VF), Unit:V@20mA
Bin Code
Min
Max
Bin Code
Min
Max
Q
63.0
125.0
K8
2.80
3.0
R
100.0
200.0
K9
2.95
3.15
S
160.0
320.0
K10
3.05
3.30
K11
3.20
3.45
Including test tolerance
Dominant Wavelength (Hue),Unit: nm@20mA
Bin Code
Min
Max
AP
519
526
AQ
524
531
Including±1nm test tolerance
CAUTIONS
1.Application Limitation :
The LED’s described here are intended to be used for ordinary electronic equipment (such as office equipment,
communication equipment and household application).Consult
HB’s sales in advance for information on
application in which exceptional quality and reliability are required, particularly when the failure or malfunction of
the LED’s may directly jeopardize life or health (such as airplanes, automobiles, traffic control equipment, life
support system and safety devices).
2.Storage :
Before opening the package :
The LEDs should be kept at 30°C or less and 85%RH or less. The LEDs should be used within a year.
After opening the package :
The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours(7
days) after opening the package.
Please avoid rapid transitions in ambient temperature in high humidity environments where condensation may occur.
3.Soldering
Do not apply any stress to the lead frame during soldering while the LED is at high temperature.
Recommended soldering condition.
Reflow Soldering :
Pre-heat 120~150°C, 120sec. MAX., Peak temperature : 240°C Max. Soldering time : 10 sec Max.
Soldering Iron : (Not recommended)
Temperature 300°C Max., Soldering time : 3 sec. Max.(one time only), power dissipation of iron : 20W Max. use
SN60 solder of solder with silver content and don’t to touch LED lens when soldering.
DRAWING NO. : DS-74-03-0008
DATE :
2004-06-07
PAGE
8 of 10
相關PDF資料 |
PDF描述 |
|---|---|
| 934056811127 | 61 A, 55 V, 0.019 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-220AB |
| 934056812118 | 61 A, 55 V, 0.019 ohm, N-CHANNEL, Si, POWER, MOSFET |
| 934056816112 | 40 MHz - 870 MHz RF/MICROWAVE WIDE BAND HIGH POWER AMPLIFIER |
| 934056817115 | 2000 mA, 40 V, PNP, Si, SMALL SIGNAL TRANSISTOR |
| 934056819118 | 4.8 A, 200 V, 0.8 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-252AA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 0603LS-101X | 制造商:Coilcraft Inc 功能描述:RF inductor, ferrite core, 2% tol, SMT, RoHS |
| 0603LS-101XGL | 制造商:Coilcraft Inc 功能描述:RF inductor, ferrite core, 2% tol, SMT, RoHS |
| 0603LS-101XGLB | 功能描述:固定電感器 RF Chip Inductor 0.1 uH 2 % 1.4 A RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| 0603LS-101XGLC | 功能描述:固定電感器 RF Chip Inductor 0.1 uH 2 % 1.4 A RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| 0603LS-101XJL | 制造商:Coilcraft Inc 功能描述:RF inductor, ferrite core, 5% tol, SMT, RoHS |
發布緊急采購，3分鐘左右您將得到回復。