- 您現在的位置：買賣IC網 > PDF目錄24796 > 07-AP863 THERMAL PRINTER PORTABLE PDF資料下載
參數資料
| 型號： | 07-AP863 |
| 英文描述： | THERMAL PRINTER PORTABLE |
| 中文描述： | 便攜式熱敏打印機 |
| 文件頁數： | 7/14頁 |
| 文件大?。?/td> | 96K |
| 代理商： | 07-AP863 |
Ap863 Users’ Guide Page 2 of 14
1
INTRODUCTION
This document is a Users' Guide, written for the person connecting and using the Able Systems
Ap863 thermal printer. Please read this Guide carefully before making any connection.
A separate document, the Programmers' Guide for the Ap863 Printer, provides details of the control
codes, and describes the internal operation of this product. The Ap863 is part of the Ap800 Series of
electronic printers and shares many features of the range.
2
MODES OF OPERATION
The Ap863 has three operating modes, when not actually printing:
"Idle Mode": ready to accept data, but no data are in the buffer awaiting printing, and the
printer motor is not running;
“Sleep Mode": effectively switched off and awaiting either a press on the paper feed button,
connection of the external charger, or some external data to exit sleep mode and enter idle
mode;
"Spooling Mode": active, but storing data for later printing.
Modes are indicated by different colour combinations on the front-panel LED (see section 5).
No light is emitted in sleep mode.
No hardware power switch is fitted, as power control is either automatic or by command from the host
computer. To save power, the printer enters sleep mode after a period of inactivity, factory-set to 30
seconds, but programmable from the host. It can also be programmed to stay idle indefinitely or to go
to sleep on command.
2.1
IDLE MODE
In idle mode, the printer is ready to receive data, which will be printed as soon as complete lines or
graphics patterns are decoded. It responds to the paper feed button in the normal way, and can also
produce a demonstration print (see below). Power consumption is such that a fully-charged battery
pack would last up to 10 hours, but the printer will normally switch from idle mode into sleep mode
when there is no activity, extending battery life.
2.2
SLEEP MODE
In sleep mode, power consumption is negligible, but data stored in the buffer are lost. Special
routines allow for data to be printed out automatically before going to sleep. User programmable
settings such as Baud rate and operational preferences are, however, retained during sleep mode or
battery replacement. The system designer can maximise battery life by arranging that the printer is
generally in sleep mode, except when printing or sending status data.
The printer enters sleep mode as follows:
by command from the host;
at the end of the (programmable) period of inactivity.
But, the Ap863 will never enter sleep mode when:
a charger is connected;
in spooling mode (see below);
The printer is woken up from sleep mode as follows:
by a data stream from the host: a certain period of logical '0' bits is required, typically a
string of 50 NUL characters at 9,600 Baud. These data will be lost. There is a delay of up
to 100 ms before the serial output lines are established and the printer is ready to accept
data;
by pressing and releasing the paper feed button;
by connecting the external battery charger.
When the Ap863 is used with either the direct mains powered PSU or the direct vehicle adaptor, no
external charger is required. However, making a connection from a PC handshaking output (DTR or
CSR) to the ‘Charger’ input may be used to force the Ap863 to wake and sleep under PC control.
相關PDF資料 |
PDF描述 |
|---|---|
| 07-AP890 | IMPACT PRINTER PORTABLE |
| 07-AP892 | IMPACT PRINTER PORTABLE |
| 935245640118 | HCT SERIES, 1-INPUT INVERT GATE, PDSO5 |
| 935245640165 | HCT SERIES, 1-INPUT INVERT GATE, PDSO5 |
| 935245650125 | HC/UH SERIES, 1-INPUT INVERT GATE, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 07-AP892 | 制造商:ABLE SYSTEMS 功能描述:PRINTER IMPACT PORTABLE 制造商:ABLE SYSTEMS 功能描述:PRINTER, IMPACT PORTABLE |
| 07B003-000 | 功能描述:RPC-7 50OHM MICROWAVE BEAD 制造商:rosenberger north america 系列:- 零件狀態:在售 連接器樣式:RPC-7 配件類型:磁珠 配套使用產品/相關產品:RPC-7 連接器 基體材料:黃銅 基體表面:金 特性:- 顏色:金色 中心觸頭材料:金 中心觸頭表面:金 標準包裝:100 |
| 07B1003JF | 制造商:Vishay Dale 功能描述:THERM NTC 100K OHM 5% 26 AWG RAD |
| 07B2003JF | 制造商:Vishay Dale 功能描述:THERM NTC 200K OHM 5% 26 AWG RAD |
| 07B5002JF | 制造商:Vishay Dale 功能描述:THERM NTC 50K OHM 5% 26 AWG RAD |
發布緊急采購，3分鐘左右您將得到回復。