- 您現在的位置：買賣IC網 > PDF目錄3909 > 101-0405 (Rabbit Semiconductor)MODULE RABBITCORE RCM2010 PDF資料下載
參數資料
| 型號： | 101-0405 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 59/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | MODULE RABBITCORE RCM2010 |
| 標準包裝： | 1 |
| 系列： | RabbitCore® |
| 模塊/板類型： | MPU 核心模塊 |
| 適用于相關產品： | RCM2010 |
| 其它名稱： | 316-1009 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
58
RabbitCore RCM2000
B.4 Using the Prototyping Board
The Prototyping Board is actually both a demonstration board and a prototyping board. As
a demonstration board, it can be used to demonstrate the functionality of the RCM2000
right out of the box without any modifications to either board. There are no jumpers or dip
switches to configure or misconfigure on the Prototyping Board so that the initial setup is
very straightforward.
The Prototyping Board comes with the basic components necessary to demonstrate the
operation of the RCM2000. Two LEDs (DS2 and DS3) are connected to PA0 and PA1, and
two switches (S2 and S3) are connected to PB2 and PB3 to demonstrate the interface to
the Rabbit 2000 microprocessor. Reset switch S1 is the hardware reset for the RCM2000.
To maximize the availability of RCM2000 resources, the demonstration hardware (LEDs
and switches) on the Prototyping Board may be disconnected. This is done by cutting the
traces below the silk-screen outline of header JP1 on the bottom side of the Prototyping
Board. Figure B-4 shows the four places where cuts should be made. An exacto knife
would work nicely to cut the traces. Alternatively, a small standard screwdriver may be
carefully and forcefully used to wipe through the PCB traces.
Figure B-4. Where to Cut Traces to Permanently Disable
Demonstration Hardware on Prototyping Board
The power LED (PWR) and the RESET switch remain connected. Jumpers across the
appropriate pins on header JP1 can be used to reconnect specific demonstration hardware
later if needed.
S2
PB3
PB2
PA1
PA0
DS3
S3
DS2
Cut
JP1
Bottom Side
相關PDF資料 |
PDF描述 |
|---|---|
| 101-0404 | MODULE RABBITCORE RCM2000 |
| 006200505130000+ | CONN FFC/FPC 5POS 1MM R/A SMD |
| 006208505110000 | CONN FFC/FPC 5POS 1MM ZIF SMD |
| 006208505110000+ | CONN FFC/FPC 5POS 1MM ZIF SMD |
| 395-030-541-204 | CARD EDGE 30POS DL .100X.200 BLK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 101-0406 | 功能描述:開發板和工具包 - 其他處理器 Cloning Board RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| 1010-406 | 制造商:MISCELLANEOUS 功能描述: |
| 101-040600-14 | 制造商:Distributed By MCM 功能描述:RJ11 PLUGS STRANDED FLAT WIREPK10 |
| 101-040600-24 | 制造商:Distributed By MCM 功能描述:RJ11 PLUGS SOLID FLAT WIRE PK10 |
| 101-040610-14 | 制造商:Distributed By MCM 功能描述:RJ11 PLUGS STRANDEDROUND WIRE PK10 |
發布緊急采購，3分鐘左右您將得到回復。