channe" />
參數資料
型號： 101-0654
廠商： Rabbit Semiconductor
文件頁數： 27/110頁
文件大?。?/td> 0K
描述： INTERFACE OP6800 W/ETHERNET 512K
標準包裝： 10
系列： SBC
模塊/板類型： 單板計算機模塊
適用于相關產品： OP6800
User’s Manual
19
3.3 Serial Communication
The OP6800 has two RS-232 serial ports, which can be configured as one RS-232 serial
channel (with RTS/CTS) or as two RS-232 (3-wire) channels using the serMode software
function call. Table 3 summarizes the options.
The OP6800 also has one RS-485 serial channel and one CMOS serial channel. The
CMOS serial channel serves as the programming port.
All four serial ports operate in an asynchronous mode. An asynchronous port can handle 7
or 8 data bits. A 9th bit address scheme, where an additional bit is sent to mark the first byte
of a message, is also supported. Serial Port A, the CMOS programming port, can be oper-
ated alternately in the clocked serial mode. In this mode, a clock line synchronously clocks
the data in or out. Either of the two communicating devices can supply the clock. The
OP6800 boards typically use all four ports in the asynchronous serial mode. Serial Ports B
and C are used for RS-232 communication, and Serial Port D is used for RS-485 commu-
nication. The OP6800 uses an 11.0592 MHz crystal, which is doubled to 22.1184 MHz. At
this frequency, the OP6800 supports standard asynchronous baud rates up to a maximum
of 230,400 bps.
3.3.1 RS-232
The OP6800 RS-232 serial communication is supported by an RS-232 transceiver. This
transceiver provides the voltage output, slew rate, and input voltage immunity required to
meet the RS-232 serial communication protocol. Basically, the chip translates the Rabbit
2000’s CMOS/TTL signals to RS-232 signal levels. Note that the polarity is reversed by
an RS-232 circuit so that a +5 V input becomes approximately -10 V and 0 V is output as
+10 V. The RS-232 transceiver also provides the proper line loading for reliable commu-
nication.
RS-232 can be used effectively at the OP6800’s maximum baud rate for distances of up to
15 m.
3.3.2 RS-485
The OP6800 has one RS-485 serial channel, which is connected to the Rabbit 2000 Serial
Port D through an RS-485 transceiver. The half-duplex communication uses the Rabbit
2000’s PB6 pin to control the transmit enable on the communication line.
The OP6800 can be used in an RS-485 multidrop network. Connect the 485+ to 485+ and
485– to 485– using single twisted-pair wires (nonstranded, tinned) as shown in Figure 11.
Note that a common ground is recommended.
Table 3. Serial Communication Configurations
Mode
Serial Port
B
C
D
0
RS-232, 3-wire
RS-485
1
RS-232, 5-wire
CTS/RTS
RS-485
相關PDF資料
PDF描述
046232108015800 CONN FFC/FPC 8POS 1MM VERT SMD
395-030-520-201 CARD EDGE 30POS DL .100X.200 BLK
20-101-0463 COMPUTER SINGLE-BOARD BL2120
20-101-1220 COMPUTER SINGLE-BOARD BL4S200
006200512230000+ CONN FFC/FPC 12POS 1MM R/A SMD
相關代理商/技術參數
參數描述
101-0655 功能描述:開發軟件 SNMP Module CD RoHS:否 制造商:Atollic Inc. 產品:Compilers/Debuggers 用于:ARM7, ARM9, Cortex-A, Cortex-M, Cortex-R Processors
10106551-JCB64LF 功能描述:板對板與夾層連接器 TRX EXT H-7ZCND0982 JRC RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A
10106552-NFB71LF 功能描述:板對板與夾層連接器 NFB71LF10106552F.NEC RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A
10106555-002LF 制造商:FCI 功能描述:511-526F-USB 制造商:FCI 功能描述:OEM ITEM 511-526F-USB
101-0656 功能描述:開發軟件 PPP Module CD RoHS:否 制造商:Atollic Inc. 產品:Compilers/Debuggers 用于:ARM7, ARM9, Cortex-A, Cortex-M, Cortex-R Processors
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*