參數資料
型號: 20-101-1139
廠商: Rabbit Semiconductor
文件頁數: 64/124頁
文件大?。?/td> 0K
描述: RCM4310 RABBITCORE
產品培訓模塊: WiFi Authentication
標準包裝: 1
系列: RabbitCore®
模塊/板類型: MPU 核心模塊
適用于相關產品: RCM4310
其它名稱: 316-1142
RabbitCore RCM4300 User’s Manual
44
4.5 Other Hardware
4.5.1 Clock Doubler
The RCM4300 takes advantage of the Rabbit 4000 microprocessor’s internal clock doubler.
A built-in clock doubler allows half-frequency crystals to be used to reduce radiated
emissions. The 58.98 MHz frequency specified for the RCM4300 model is generated
using a 29.49 MHz crystal.
The clock doubler may be disabled if 58.98 MHz clock speeds are not required. Disabling
the Rabbit 4000 microprocessor’s internal clock doubler will reduce power consumption
and further reduce radiated emissions. The clock doubler is disabled with a simple config-
uration macro as shown below.
4.5.2 Spectrum Spreader
The Rabbit 4000 features a spectrum spreader, which helps to mitigate EMI problems. The
spectrum spreader is on by default, but it may also be turned off or set to a stronger setting.
The means for doing so is through a simple configuration macro as shown below.
NOTE: Refer to the Rabbit 4000 Microprocessor User’s Manual for more information
on the spectrum-spreading setting and the maximum clock speed.
1. Select the “Defines” tab from the Dynamic C Options > Project Options menu.
2. Add the line CLOCK_DOUBLED=0 to always disable the clock doubler.
The clock doubler is enabled by default, and usually no entry is needed. If you need to
specify that the clock doubler is always enabled, add the line CLOCK_DOUBLED=1 to
always enable the clock doubler.
3. Click OK to save the macro. The clock doubler will now remain off whenever you are
in the project file where you defined the macro.
1. Select the “Defines” tab from the Dynamic C Options > Project Options menu.
2. Normal spreading is the default, and usually no entry is needed. If you need to specify
normal spreading, add the line
ENABLE_SPREADER=1
For strong spreading, add the line
ENABLE_SPREADER=2
To disable the spectrum spreader, add the line
ENABLE_SPREADER=0
NOTE: The strong spectrum-spreading setting is not recommended since it may limit
the maximum clock speed or the maximum baud rate. It is unlikely that the strong set-
ting will be used in a real application.
3. Click OK to save the macro. The spectrum spreader will now remain off whenever you
are in the project file where you defined the macro.
相關PDF資料
PDF描述
20-101-1154 MODULE RCM4120 RABBITCORE
20-101-1197 MODULE RABBITCORE RCM3910 ROHS
20-101-1215 MCU RCM4050 RABBITCORE
20-101-1246 CORE MODULE RCM5400W
20-101-1260 BL5S220 SBC (RCM5400-BASED)
相關代理商/技術參數
參數描述
20-101-1140 功能描述:WiFi/802.11模塊 RCM4400W CORE MODULE Wi-Fi/802.11 RoHS:否 制造商:Taiyo Yuden 支持協議:802.11 b/g/n 頻帶: 數據速率:150 Mbps 接口類型:SDIO 傳輸功率(最大): 天線連接器類型: 工作電源電壓:3.4 V to 5.5 V 傳輸供電電流: 接收供電電流: 最大工作溫度:+ 80 C 尺寸:35 mm x 15 mm x 2.9 mm
20-101-1153 功能描述:子卡和OEM板 RCM4300 Proto board RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-1154 功能描述:模塊化系統 - SOM RCM4120 RabbitCore- Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1170 功能描述:Zigbee/802.15.4模塊 RCM4510W CORE MODULE RoHS:否 制造商:Digi International 頻帶:902 MHz to 928 MHz 視線范圍: 數據速率: 靈敏度: 工作電源電壓:2.4 V to 3.6 V 傳輸供電電流:215 mA 接收供電電流:26 mA 輸出功率:250 mW 天線連接器類型:Wire 最大工作溫度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
20-101-1179 功能描述:模塊化系統 - SOM RCM3209 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in