4
FN9271.1
November 30, 2006
Absolute Maximum Ratings
Thermal Information
Supply Voltage (CRDL, USB) . . . . . . . . . . . . . . . . . . . .-0.3V to 28V
Other Input Voltage (EN, USBON, ICDL, IMIN, BAT) . . .-0.3V to 7V
Open-Drain Pull-Up Voltage (PPR, CHG) . . . . . . . . . . . .-0.3V to 7V
ESD Rating
Human Body Model (JEDEC JESD22-A114-D) . . . . . . . . . .7000V
Machine Model (JEDEC JESD22-A115-A). . . . . . . . . . . . . . .300V
Recommended Operating Conditions
Ambient Temperature Range. . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage (USB Pin) . . . . . . . . . . . . . . . . . . . . . . 4.3V to 5.5V
Supply Voltage (CRDL Pin) . . . . . . . . . . . . . . . . . . . . . . 4.3V to 24V
Typical Cradle Charge Current . . . . . . . . . . . . . . . . . . 100mA to 1A
Typical USB Charge Current . . . . . . . . . . . . . . . . . . . . . . . . . 380mA
Thermal Resistance
DFN Package (Notes 1, 2). . . . . . . . . .
Maximum Junction Temperature (Plastic Package) . . . . . . .+150°C
Maximum Storage Temperature Range. . . . . . . . . .-65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . .+300°C
θ
JA
(°C/W)
40
θ
JC
(°C/W)
2.5
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
+
150°C max junction temperature is intended for short periods of time to prevent shortening the lifetime. Operation close to +150°C junction may trigger the shutdown of
the device even before +150°C, since this number is specified as typical.
NOTES:
1.
θ
JA
is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
2. For theta
θ
JC
the "case temp." location is the center of the exposed metal pad on the package underside.
Electrical Specifications
Typical Values Are Tested at USB = CRDL = 5V and ambient temperature is at +25°C, Unless Otherwise Noted.
All Maximum and Minimum Values Are Guaranteed Under the Recommended Operating Conditions
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
POWER-ON RESET
Rising USB/CRDL Threshold
3.4
3.9
4.2
V
Falling USB/CRDL Threshold
3.2
3.7
4.0
V
VIN-BAT OFFSET VOLTAGE
Rising Edge
V
OS
V
BAT
= 4.0V, use CHG pin to indicate the
comparator output (Note 3)
-
150
250
mV
Falling Edge
V
OS
20
80
-
mV
STANDBY CURRENT
BAT Pin Sink Current
I
STANDBY
EN = HIGH or both inputs are floating
-
0.05
0.5
μ
A
CRDL Pin Supply Current
I
CRDL
EN = HIGH
-
150
220
μ
A
USB Pin Supply Current
I
USB
-
150
220
μ
A
CRDL/USB Pin Supply Current
EN = LOW or floating
-
0.55
0.8
mA
VOLTAGE REGULATION
Output Voltage
V
CH
Load = 10mA
4.158
4.2
4.242
V
Output Voltage
V
CH
Load = 10mA (T
j
= +25°C)
4.174
4.2
4.226
V
CRDL PMOS On Resistance
V
BAT
= 3.8V, I
CHARGER
= 0.3A, (T
j
= +25°C)
200
600
850
m
Ω
USB PMOS On Resistance
V
BAT
= 3.8V, I
CHARGER
= 0.3A, (T
j
= +25°C)
200
600
850
m
Ω
CHARGE CURRENT
(Note 4)
ICDL Pin Output Voltage
V
ICDL
V
BAT
= 3.8V
1.19
1.22
1.25
V
CRDL Input Constant Charge Current
I
CHARGE
R
ICDL
= 12.4k
Ω,
VBAT: 2.7 - 3.8V
520
550
580
mA
CRDL Input Trickle Charge Current
I
TRICKLE
R
ICDL
= 12.4k
Ω
, V
BAT
= 2.2V
Given as a % of the CRDL I
CHARGE
16
18
20
%
CRDL and USB End-of-Charge Threshold
I
MIN
R
IMIN
= 10.0k
Ω
46.5
55
63.5
mA
ISL9214