- 您現在的位置：買賣IC網 > PDF目錄371374 > 22505 AMD Test Interface Port Board User＇s Manual? 2.62MB (PDF) PDF資料下載
參數資料
| 型號： | 22505 |
| 英文描述： | AMD Test Interface Port Board User＇s Manual? 2.62MB (PDF) |
| 中文描述： | AMD測試接口端口板用戶手冊？ 2.62MB（PDF格式） |
| 文件頁數： | 33/78頁 |
| 文件大?。?/td> | 2691K |
| 代理商： | 22505 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
Test Interface Port Board User’s Manual
2-9
Interrupt Enable Register:
This register enables the following serial port
interrupts: modem status, receiver line status, transmitter holding empty,
received data available, and time-out interrupts (when DLAB is 0).
Interrupt Identification Register:
This is a read-only register used to identify
UART interrupts.
FIFO Control Register:
This is a write-only register used to enable and control
the FIFO in 16650-compatible mode.
Line Status Register:
This register shows the status of the data transfer,
including parity and framing errors, in addition to break and empty indicators.
Modem Control Register:
This register is used to enable interrupts and
loopback diagnostic mode, and to assert RTS and DTR.
Modem Status Register:
This register contains both real-time and latched
status bits for DCD, RIN, DSR, and CTS.
Scratch Pad Register:
This is a general purpose I/O location used to hold
temporary data and is not required for serial data transfer.
Configuring the Serial Port for DTE
Because the TIP board provides information to a terminal, it is considered data
carrier equipment (DCE), and the serial ports are configured accordingly in its
default design. You can also configure the TIP board to serve as data terminal
equipment (DTE) if necessary.
To reconfigure serial port 0 to operate as DTE, use the following procedure:
1. Depopulate resistors R24 through R31.
2. Populate resistors R44 through R50, located on the back of the board.
3. A gender changer is now required for serial port 0, either on the TIP board end
or the connecting cable end.
To reconfigure serial port 1 to operate as DTE, use the following procedure:
1. Depopulate resistors R34 through R41.
2. Populate resistors R51 through 57, located on the back of the board.
3. A gender changer is now required for serial port 1, either on the TIP board end
or the connecting cable end.
相關PDF資料 |
PDF描述 |
|---|---|
| 22505_1 | AMD Test Interface Port Board Schematics? 149KB (PDF) |
| 225224541474 | Leaded ceramic multilayer capacitors |
| 225222521101 | Leaded ceramic multilayer capacitors |
| 225222521102 | Leaded ceramic multilayer capacitors |
| 225222521103 | Leaded ceramic multilayer capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 22505_1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AMD Test Interface Port Board Schematics? 149KB (PDF) |
| 2250-5003UB | 制造商:3M Electronic Products Division 功能描述:CONNECTOR |
| 2250504-1 | 功能描述:CONN MAGJACK 1PORT 2.5G BASE-T 制造商:trp connector b.v. 系列:MagJack? 包裝:托盤 零件狀態:在售 連接器類型:RJ45 端口數:1 排數:1 應用:2.5G Base-T，AutoMDIX，以太網供電（PoE） 安裝類型:通孔 朝向:90°角（直角） 端接:焊接 板上高度:0.536"（13.61mm） LED 顏色:不包含 LED 每插孔芯數:8 屏蔽:屏蔽式，EMI指 特性:板導軌 凸片方向:上 觸頭材料:磷青銅 觸頭鍍層:金 工作溫度:-40°C ~ 85°C 觸頭鍍層厚度:50μin（1.27μm） 屏蔽材料:不銹鋼 外殼材料:熱塑塑膠 標準包裝:90 |
| 225050411527 | 制造商:Yageo Corporation 功能描述:MLCC 1812 22PF 4KV NP0 5% |
| 225050411532 | 制造商:Yageo Corporation 功能描述:MLCC 1812 47PF 4KV NP0 5% |
發布緊急采購，3分鐘左右您將得到回復。