- 您現在的位置：買賣IC網 > PDF目錄371434 > 28F008SA-L (Intel Corp.) 8-MBIT (1 MBIT x 8) FLASHFILETM MEMORY PDF資料下載
參數資料
| 型號： | 28F008SA-L |
| 廠商： | Intel Corp. |
| 英文描述： | 8-MBIT (1 MBIT x 8) FLASHFILETM MEMORY |
| 中文描述： | 8兆（1兆比特× 8）FLASHFILETM記憶 |
| 文件頁數： | 18/49頁 |
| 文件大?。?/td> | 408K |
| 代理商： | 28F008SA-L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
SMART 3 ADVANCED BOOT BLOCK
–BYTE-WIDE
E
18
PRELIMINARY
When the WSM is active, bit 7 (SR.7) of the status
register will indicate the status of the WSM; the
remaining bits in the status register indicate
whether or not the WSM was successful in
performing the desired operation (see Table 7).
3.2.3.1
Clearing the Status Register
The WSM sets status bits 1 through 7 to
“1,” and
clears bits 2, 6 and 7
to “0,” but cannot clear status
bits 1 or 3 through 5 to “0.” Because bits 1, 3, 4,
and 5 indicate various error conditions, these bits
can only be cleared by the controlling CPU through
the use of the Clear Status Register (50H)
command. By allowing the system software to
control the resetting of these bits, several
operations may be performed (such as cumulatively
programming several addresses or erasing multiple
register to determine if an error occurred during that
series. Clear the Status Register before beginning
another command or sequence. Note, again, that
the Read Array command must be issued before
data can be read from the memory array.
3.2.4
PROGRAM MODE
Programming is executed using a two-write
sequence. The Program Setup command (40H) is
written to the CUI followed by a second write which
specifies the address and data to be programmed.
The WSM will execute the following sequence of
internally timed events:
1.
Program the desired bits of the addressed
memory.
Verify that the desired bits are sufficiently
programmed.
2.
Programming of the memory results in specific bits
within an address location being changed to a “0.” If
the user attempts to program “1”s, there will be no
change of the memory cell contents and no error
occurs.
The status register indicates programming status:
while the program sequence is executing, bit 7 of
the status register is a “0.” The status register can
be polled by toggling either CE# or OE#. While
programming, the only valid commands are Read
Status Register, Program Suspend, and Program
Resume.
When programming is complete, the Program
Status bits should be checked. If the programming
operation was unsuccessful, bit SR.4 of the status
register is set to indicate a program failure. If SR.3
is set then V
PP
was not within acceptable limits, and
the WSM did not execute the program command. If
SR.1 is set, a program operation was attempted to
a locked block and the operation was aborted.
The status register should be cleared before
attempting the next operation. Any CUI instruction
can follow after programming is completed;
however, to prevent inadvertent status register
reads, be sure to reset the CUI to read array mode.
3.2.4.1
Suspending and Resuming
Program
The Program Suspend command allows program
suspension in order to read data in other locations
of memory. Once the programming process starts,
writing the Program Suspend command to the CUI
requests that the WSM suspend the program
sequence (at predetermined points in the program
algorithm). The device continues to output status
register data after the Program Suspend command
is written. Polling status register bits SR.7 and SR.2
will determine when the program operation has
been suspended (both will be set to “1”).
t
WHRH1
/t
EHRH1
specify the program suspend latency.
A Read Array command can now be written to the
CUI to read data from blocks other than that which
is suspended. The only other valid commands,
while program is suspended, are Read Status
Register and Program Resume. After the Program
Resume command is written to the flash memory,
the WSM will continue with the program process
and status register bits SR.2 and SR.7 will
automatically be cleared. After the Program
Resume
command
is
automatically outputs status register data when
read (see Figure 7, Program Suspend/Resume
Flowchart). V
must remain at the same V
PP
level
used for program while in program suspend mode.
RP# must also remain at V
IH.
written,
the
device
3.2.4.2
V
Supply Voltage during
Program
V
PP
supply voltage considerations are outlined in
Section 3.4.
相關PDF資料 |
PDF描述 |
|---|---|
| 28F008S3 | 3 V FlashFile Memory(3V閃速存儲器) |
| 28F016S3 | 3 V FlashFile Memory(3V閃速存儲器) |
| 28F008S5 | 8-MBIT 5 VOLT FlashFile Memory(8M位5V閃速存儲器) |
| 28F016S5 | 16-MBIT 5V FlashFile Memory(16M位5V閃速存儲器) |
| 28F008SC | 8-MBIT SmartVoltage FlashFile Memory(8M位智能電壓閃速存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F008SAT-ZW | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 28F008SC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BYTE-WIDE SmartVoltage FlashFile MEMORY FAMILY 4. 8. AND 16 MBIT |
| 28F010 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:1024K (128K x 8) CMOS FLASH MEMORY |
| 28F0101024K | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:28F010 1024K (128K X 8) CMOS FLASH MEMORY |
| 28F010120EI | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。