參數資料
型號： 28F032C3
英文描述： 3 VOLT ADVANCED+ BOOT BLOCK. 8-. 16-. 32-MBIT FLASH MEMORY FAMILY
中文描述： 3伏高級啟動塊。 8 -. 16 -. 32 - Mbit閃存家庭
文件頁數： 14/59頁
文件大小： 384K
代理商： 28F032C3
3 VOLT ADVANCED+ BOOT BLOCK
E
14
PRODUCT PREVIEW
3.2.5
PROGRAM MODE
Programming is executed using a two-write
sequence. The Program Setup command (40H) is
written to the CUI followed by a second write which
specifies the address and data to be programmed.
The WSM will execute a sequence of internally
timed events to program desired bits of the
addressed location, then verify the bits are
sufficiently programmed. Programming the memory
results in specific bits within an address location
being changed to a
“0.” If the user attempts to
program “1”s, the memory cell contents do not
change and no error occurs.
The status register indicates programming status:
while the program sequence executes, status bit 7
is “0.” The status register can be polled by toggling
either CE# or OE#. While programming, the only
valid commands are Read Status Register,
Program Suspend, and Program Resume.
When programming is complete, the Program
Status bits should be checked. If the programming
operation was unsuccessful, bit SR.4 of the status
register is set to indicate a program failure. If SR.3
is set then V
PP
was not within acceptable limits, and
the WSM did not execute the program command. If
SR.1 is set, a program operation was attempted on
a locked block and the operation was aborted.
The status register should be cleared before
attempting the next operation. Any CUI instruction
can follow after programming is completed;
however, to prevent inadvertent status register
reads, be sure to reset the CUI to read array mode.
3.2.5.1
Suspending and Resuming
Program
The Program Suspend command halts an in
-
progress program operation so that data can be
read from other locations of memory. Once the
programming process starts, writing the Program
Suspend command to the CUI requests that the
WSM
suspend
the
program
predetermined points in the program algorithm).
The device continues to output status register data
after the Program Suspend command is written.
Polling status register bits SR.7 and SR.2 will
determine when the program operation has been
suspended (both will be set to “1”). t
WHRH1
/t
EHRH1
specify the program suspend latency.
sequence
(at
A Read Array command can now be written to the
CUI to read data from blocks other than that which
is suspended. The only other valid commands,
while program is suspended, are Read Status
Register, Read Configuration, Read Query, and
Program Resume. After the Program Resume
command is written to the flash memory, the WSM
will continue with the programming process and
status register bits SR.2 and SR.7 will automatically
be cleared. The device automatically outputs status
register data when read (see Figure 13 in Appendix
B,
Program Suspend/Resume Flowchart
) after the
Program Resume command is written. V
PP
must
remain at the same V
PP
level used for program
while in program suspend mode. RP# must also
remain at V
IH
.
3.2.6
ERASE MODE
To erase a block, write the Erase Set
-
up and Erase
Confirm commands to the CUI, along with an
address identifying the block to be erased. This
address is latched internally when the Erase
Confirm command is issued. Block erasure results
in all bits within the block being set to “1.” Only one
block can be erased at a time. The WSM will
execute a sequence of internally timed events to
program all bits within the block to “0,” erase all bits
within the block to “1,” then verify that all bits within
the block are sufficiently erased. While the erase
executes, status bit 7 is a “0.”
When the status register indicates that erasure is
complete, check the erase status bit to verify that
the erase operation was successful. If the Erase
operation was unsuccessful, SR.5 of the status
register will be set to a “1,” indicating an erase
failure. If V
was not within acceptable limits after
the Erase Confirm command was issued, the WSM
will not execute the erase sequence; instead, SR.5
of the status register is set to indicate an erase
error, and SR.3 is set to a “1” to identify that V
PP
supply voltage was not within acceptable limits.
After an erase operation, clear the status register
(50H) before attempting the next operation. Any
CUI instruction can follow after erasure is
completed; however, to prevent inadvertent status
register reads, it is advisable to place the flash in
read array mode after the erase is complete.
相關PDF資料
PDF描述
28F160F3 5V/3.3V or Adjustable, Low-Dropout, Low-IQ, 500mA Linear Regulators
28F800F3 3 Volt Fast Boot Block Flash Memory(3 V 8M位快速引導塊閃速存儲器)
28F160F3 16MBIT Fast Boot Block Flash Memory(16兆位的快速引導塊閃速存儲器)
28F2001BX-T 5V/3.3V or Adjustable, Low-Dropout, Low-IQ, 500mA Linear Regulators
28F256 FASTENERS, TIES CABLE
相關代理商/技術參數
參數描述
28F0330-2SR 制造商:Steward/Laird Tech 功能描述:
28F04181SR 制造商:STEWARD 功能描述:New
28F0428-0T0 功能描述:FERRITE FILTER 4 LINE PCB RoHS:是 類別:濾波器 >> 鐵氧體磁珠和芯片 系列:- 標準包裝:1,000 系列:EMI1812 頻率對應阻抗:120 歐姆 @ 100MHz 額定電流:200mA DC 電阻(DCR):最大 400 毫歐 濾波器類型:差模 - 單線 封裝/外殼:1812（4532 公制） 安裝類型:表面貼裝 包裝:帶卷 (TR) 高度（最大）:0.069"（1.75mm） 尺寸/尺寸:0.177" L x 0.126" W（4.50mm x 3.20mm） 其它名稱:Q1712807A
28F0430-2SR 制造商:Laird Technologies Inc 功能描述:28F0430-2SR
28F0430-4SR 制造商:Laird Technologies Inc 功能描述: 制造商:Laird Technologies Inc 功能描述:4 FUNCTIONS, 9 A, FERRITE BEAD
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*