參數資料
型號： 28F032C3
英文描述： 3 VOLT ADVANCED+ BOOT BLOCK. 8-. 16-. 32-MBIT FLASH MEMORY FAMILY
中文描述： 3伏高級啟動塊。 8 -. 16 -. 32 - Mbit閃存家庭
文件頁數： 20/59頁
文件大?。?/td> 384K
代理商： 28F032C3
3 VOLT ADVANCED+ BOOT BLOCK
E
20
PRODUCT PREVIEW
3.3.5
READING A BLOCK’S LOCK STATUS
The lock status of every block can be read in the
Configuration Read mode of the device. To enter
this mode, write 90H to the device. Subsequent
reads at Block Address + 00002 will output the lock
status of that block. The lock status is represented
by the lowest two output pins, DQ
0
and DQ
1
. DQ
0
indicates the Block Lock/Unlock status and is set by
the Lock command and cleared by the Unlock
command. It is also automatically set when entering
Lock-Down. DQ
1
indicates Lock-Down status and is
set by the Lock-Down command. It cannot be
cleared by software, only by device reset or power-
down.
Table 8. Block Lock Status
Item
Address
Data
Block Lock Configuration
XX002
LOCK
Block Is Unlocked
DQ
0
= 0
Block Is Locked
DQ
0
= 1
Block Is Locked-Down
DQ
1
= 1
3.3.6
LOCKING OPERATIONS DURING
ERASE SUSPEND
Changes to block lock status can be performed
during an erase suspend by using the standard
locking command sequences to unlock, lock, or
lock-down a block. This is useful in the case when
another block needs to be updated while an erase
operation is in progress.
To change block locking during an erase operation,
first write the erase suspend command (B0H), then
check the status register until it indicates that the
erase operation has been suspended. Next write
the desired lock command sequence to a block and
the lock status will be changed. After completing
any desired lock, read, or program operations,
resume the erase operation with the Erase Resume
command (D0H).
If a block is locked or locked-down during a
suspended erase of the same block, the locking
status bits will be changed immediately, but when
the erase is resumed, the erase operation will
complete.
Locking operations cannot be performed during a
program suspend. Refer to Appendix A for detailed
information on which commands are valid during
erase suspend.
3.3.7
STATUS REGISTER ERROR
CHECKING
Using nested locking or program command
sequences during erase suspend can introduce
ambiguity into status register results.
Since locking changes are performed using a two
cycle command sequence, e.g., 60H followed by
01H to lock a block, following the Configuration
Setup command (60H) with an invalid command will
produce a lock command error (SR.4 and SR.5 will
be set to 1) in the status register. If a lock
command error occurs during an erase suspend,
SR.4 and SR.5 will be set to 1, and will remain at 1
after the erase is resumed. When erase is
complete, any possible error during the erase
cannot be detected via the status register because
of the previous locking command error.
A similar situation happens if an error occurs during
a program operation error nested within an erase
suspend.
相關PDF資料
PDF描述
28F160F3 5V/3.3V or Adjustable, Low-Dropout, Low-IQ, 500mA Linear Regulators
28F800F3 3 Volt Fast Boot Block Flash Memory(3 V 8M位快速引導塊閃速存儲器)
28F160F3 16MBIT Fast Boot Block Flash Memory(16兆位的快速引導塊閃速存儲器)
28F2001BX-T 5V/3.3V or Adjustable, Low-Dropout, Low-IQ, 500mA Linear Regulators
28F256 FASTENERS, TIES CABLE
相關代理商/技術參數
參數描述
28F0330-2SR 制造商:Steward/Laird Tech 功能描述:
28F04181SR 制造商:STEWARD 功能描述:New
28F0428-0T0 功能描述:FERRITE FILTER 4 LINE PCB RoHS:是 類別:濾波器 >> 鐵氧體磁珠和芯片 系列:- 標準包裝:1,000 系列:EMI1812 頻率對應阻抗:120 歐姆 @ 100MHz 額定電流:200mA DC 電阻(DCR):最大 400 毫歐 濾波器類型:差模 - 單線 封裝/外殼:1812（4532 公制） 安裝類型:表面貼裝 包裝:帶卷 (TR) 高度（最大）:0.069"（1.75mm） 尺寸/尺寸:0.177" L x 0.126" W（4.50mm x 3.20mm） 其它名稱:Q1712807A
28F0430-2SR 制造商:Laird Technologies Inc 功能描述:28F0430-2SR
28F0430-4SR 制造商:Laird Technologies Inc 功能描述: 制造商:Laird Technologies Inc 功能描述:4 FUNCTIONS, 9 A, FERRITE BEAD
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*