- 您現在的位置：買賣IC網 > PDF目錄371438 > 29F004T-55 (Macronix International Co., Ltd.) 4M-BIT [512KX8] CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29F004T-55 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 4M-BIT [512KX8] CMOS FLASH MEMORY |
| 中文描述： | 4分位[512KX8]的CMOS閃存 |
| 文件頁數： | 10/39頁 |
| 文件大?。?/td> | 599K |
| 代理商： | 29F004T-55 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
10
MX29F004T/B
P/N:PM0554
REV. 1.9, OCT. 19, 2004
ERASE SUSPEND
This command only has meaning while the state ma-
chine is executing Automatic Sector Erase operation,
and therefore will only be responded during Automatic
Sector Erase operation. When the Erase Suspend com-
mand is written during a sector erase operation, the de-
vice requires a maximum of 100us to suspend the erase
operations. However, when the Erase Suspend command
is written during the sector erase time-out, the device
immediately terminates the time-out period and suspends
the erase operation. After this command has been ex-
ecuted, the command register will initiate erase suspend
mode. The state machine will return to read mode auto-
matically after suspend is ready. At this time, state ma-
chine only allows the command register to respond to
the Read Memory Array, Erase Resume and program
commands.
The system can determine the status of the program
operation using the Q7 or Q6 status bits, just as in the
standard program operation. After an erase-suspend pro-
gram operation is complete, the system can once again
read array data within non-suspended sectors.
ERASE RESUME
This command will cause the command register to clear
the suspend state and return back to Sector Erase mode
but only if an Erase Suspend command was previously
issued. Erase Resume will not have any effect in all
other conditions. Another Erase Suspend command can
be written after the chip has resumed erasing.
SET-UP AUTOMATIC PROGRAM COMMANDS
To initiate Automatic Program mode, A three-cycle com-
mand sequence is required. There are two "unlock" write
cycles. These are followed by writing the Automatic Pro-
gram command A0H.
Once the Automatic Program command is initiated, the
next WE or CE pulse causes a transition to an active
programming operation. Addresses are latched on the
falling edge, and data are internally latched on the
rising edge of the WE or CE, whichever happens first
pulse. The rising edge of WE or CE, whichever hap-
pens first also begins the programming operation. The
system is not required to provide further controls or tim-
ings. The device will automatically provide an adequate
internally generated program pulse and verify margin.
If the program operation was unsuccessful, the data on
Q5 is "1"(see Table 4), indicating the program operation
exceed internal timing limit. The automatic programming
operation is completed when the data read on Q6 stops
toggling for two consecutive read cycles and the data on
Q7 and Q6 are equivalent to data written to these two
bits, at which time the device returns to the Read mode
(no program verify command is required).
DATA POLLING-Q7
The MX29F004T/B also features Data Polling as a
method to indicate to the host system that the Auto-
matic Program or Erase algorithms are either in progress
or completed.
While the Automatic Programming algorithm is in opera-
tion, an attempt to read the device will produce the comple-
ment data of the data last written to Q7. Upon comple-
tion of the Automatic Program Algorithm an attempt to
read the device will produce the true data last written to
Q7. The Data Polling feature is valid after the rising edge
of the fourth WE or CE, whichever happens first pulse of
the four write pulse sequences for automatic program.
While the Automatic Erase algorithm is in operation, Q7
will read "0" until the erase operation is competed. Upon
completion of the erase operation, the data on Q7 will
read "1". The Data Polling feature is valid after the rising
edge of the sixth WE or CE, whichever happens first
pulse of six write pulse sequences for automatic chip/
sector erase.
The Data Polling feature is active during Automatic Pro-
gram/Erase algorithm or sector erase time-out. (see sec-
tion Q3 Sector Erase Timer)
相關PDF資料 |
PDF描述 |
|---|---|
| 29F004T-70 | 4M-BIT [512KX8] CMOS FLASH MEMORY |
| 29F004T-90 | 4M-BIT [512KX8] CMOS FLASH MEMORY |
| 29F016-12 | 16M-BIT [2M X 8] CMOS EQUAL SECTOR FLASH MEMORY |
| 29F016-90 | 16M-BIT [2M X 8] CMOS EQUAL SECTOR FLASH MEMORY |
| 29F022B-12 | 2M-BIT[256K x 8]CMOS FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29F004T-70 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512KX8] CMOS FLASH MEMORY |
| 29F004T-90 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512KX8] CMOS FLASH MEMORY |
| 29F010 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Mbit 128Kb x8, Uniform Block Single Supply Flash Memory |
| 29F01045JC | 制造商: 功能描述: 制造商:Advanced Micro Devices 功能描述: 制造商:undefined 功能描述: |
| 29F010-45JC | 制造商: 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。