參數資料
型號： 29LV800BT-90
廠商： Macronix International Co., Ltd.
英文描述： 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
中文描述： 800萬位[1Mx8/512K x16] CMOS單電壓3V時僅閃存
文件頁數： 14/63頁
文件大?。?/td> 765K
代理商： 29LV800BT-90
14
P/N:PM1062
MX29LV800BT/BB
REV. 1.3, DEC. 20, 2004
READING ARRAY DATA
The device is automatically set to reading array data
after device power-up. No commands are required to re-
trieve data. The device is also ready to read array data
after completing an Automatic Program or Automatic
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data. Af-
ter completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See Erase Suspend/Erase
Resume Commands
”
for more information on this mode.
The system must issue the reset command to re-en-
able the device for reading array data if Q5 goes high, or
while in the autoselect mode. See the "Reset Command"
section, next.
RESET COMMAND
Writing the reset command to the device resets the de-
vice to reading array data. Address bits are don't care
for this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the se-
quence cycles in a program command sequence before
programming begins. This resets the device to reading
array data (also applies to programming in Erase Sus-
pend mode). Once programming begins, however, the
device ignores reset commands until the operation is
complete.
The reset command may be written between the se-
quence cycles in an SILICON ID READ command se-
quence. Once in the SILICON ID READ mode, the reset
command must be written to return to reading array data
(also applies to SILICON ID READ during Erase Sus-
pend).
If Q5 goes high during a program or erase operation,
writing the reset command returns the device to read-
ing array data (also applies during Erase Suspend).
Pins
Manufacture code
A0
A1
VIL
VIL
VIL
VIL
VIL
VIL
VIH
VIH
Q15~Q8 Q7
00H
X
22H
X
22H
X
X
X
Q6
1
1
1
1
1
1
0
0
Q5
0
0
0
0
0
0
0
0
Q4
0
0
1
1
1
1
0
0
Q3
0
0
1
1
1
1
0
0
Q2 Q1
0
0
0
0
0
0
0
0
Q0
0
0
0
0
1
1
1
0
Code (Hex)
00C2H
C2H
22DAH
DAH
225BH
5BH
01H (Protected)
00H (Unprotected)
Word VIL
Byte
Word VIH
Byte
Word VIH
Byte
Word X
Byte X
1
1
1
1
0
0
0
0
1
1
1
1
1
1
0
0
VIL
Device code
for MX29LV800BT
Device code
for MX29LV800BB
Sector Protection
Verification
VIH
VIH
TABLE 7. SILICON ID CODE
相關PDF資料
PDF描述
29LV800BE 8M (1M x 8/512 K x 16) BIT
29LV800TE 8M (1M x 8/512 K x 16) BIT
29PL256N 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
29PS 25PS, 42PS, 44PS, 45PS and 46PS Series Pressure Switches
29SL800CB-90 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 1.8V ONLY FLASH MEMORY
相關代理商/技術參數
參數描述
29LV800TE 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8M (1M x 8/512 K x 16) BIT
29M132 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor
29M30050R008BL 制造商:Micro Plastics Inc 功能描述:
29M426 制造商:Honeywell Sensing and Control 功能描述:
29M428 功能描述:工業移動感應器和位置傳感器 RESISTIVE & OPTICAL RoHS:否 制造商:Honeywell 輸出類型:Analog - Current 電壓額定值:12 VDC to 30 VDC 線性:+/- 0.0011 % 溫度范圍:- 40 C to + 85 C 總電阻: 容差: 類型:Rotary Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*