- 您現在的位置：買賣IC網 > PDF目錄41446 > 2N6576 (ON SEMICONDUCTOR) 15 A, 60 V, NPN, Si, POWER TRANSISTOR, TO-204AA PDF資料下載
參數資料
| 型號： | 2N6576 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 功率晶體管 |
| 英文描述： | 15 A, 60 V, NPN, Si, POWER TRANSISTOR, TO-204AA |
| 封裝： | METAL, TO-3, 2 PIN |
| 文件頁數： | 11/60頁 |
| 文件大?。?/td> | 363K |
| 代理商： | 2N6576 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
4–3
Surface Mount Package Information and Tape and Reel Specifications
Motorola Bipolar Power Transistor Device Data
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads.
Solder stencils are used to screen the optimum amount.
These stencils are typically 0.008 inches thick and may be
made of brass or stainless steel. This is not the case with the
DPAK and D2PAK packages. If a 1:1 opening is used to
screen solder onto the drain pad, misalignment and/or “tomb-
stoning” may occur due to an excess of solder. For these two
packages, the opening in the stencil for the paste should be
approximately 50% of the tab area. The opening for the leads
is still a 1:1 registration. Figure 3 shows a typical stencil for
the DPAK and D2PAK packages. The pattern of the opening
in the stencil for the drain pad is not critical as long as it
allows approximately 50% of the pad to be covered with
paste.
Figure 3. Typical Stencil for DPAK and
D2PAK Packages
SOLDER PASTE
OPENINGS
STENCIL
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to mini-
mize the thermal stress to which the devices are subjected.
Always preheat the device.
The delta temperature between the preheat and soldering
should be 100
°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference should be a maximum of 10
°C.
The soldering temperature and time should not exceed
260
°C for more than 10 seconds.
When shifting from preheating to soldering, the maximum
temperature gradient shall be 5
°C or less.
After soldering has been completed, the device should be
allowed to cool naturally for at least three minutes.
Gradual cooling should be used since the use of forced
cooling will increase the temperature gradient and will
result in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
* Due to shadowing and the inability to set the wave height to
incorporate other surface mount components, the D2PAK is
not recommended for wave soldering.
相關PDF資料 |
PDF描述 |
|---|---|
| 2N6678-JQR | 15 A, 300 V, NPN, Si, POWER TRANSISTOR, TO-204AA |
| 2N6678.MOD | 15 A, 300 V, NPN, Si, POWER TRANSISTOR, TO-204AA |
| 2N6678-JQR-B | 15 A, 300 V, NPN, Si, POWER TRANSISTOR, TO-204AA |
| 2N6678-JQR-BR1 | 15 A, 300 V, NPN, Si, POWER TRANSISTOR, TO-204AA |
| 2N6715STOA | 1000 mA, 40 V, NPN, Si, SMALL SIGNAL TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 2N6576_1 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:NPN Silicon Power Darlington Transistors |
| 2N6577 | 制造商:SEME-LAB 制造商全稱:Seme LAB 功能描述:Bipolar NPN Device |
| 2N6578 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:NPN SILICON POWER DARLINGTON TRANSISTORS |
| 2N6579 | 制造商:Microsemi Corporation 功能描述:TRANS GP BJT NPN 350V 12A 3PIN TO-3 - Bulk |
| 2N657A | 功能描述:兩極晶體管 - BJT Small Signal Transistor Gen Purp RoHS:否 制造商:STMicroelectronics 配置: 晶體管極性:PNP 集電極—基極電壓 VCBO: 集電極—發射極最大電壓 VCEO:- 40 V 發射極 - 基極電壓 VEBO:- 6 V 集電極—射極飽和電壓: 最大直流電集電極電流: 增益帶寬產品fT: 直流集電極/Base Gain hfe Min:100 A 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PowerFLAT 2 x 2 |
發布緊急采購，3分鐘左右您將得到回復。