Document Number: 23089
Revision 14-May-02
www.vishay.com
14
307C Overcurrent Thermistors
Vishay Cera-Mite
ceramite.support@vishay.com
PTCR Overcurrent Protection
VISHAY
HOLD (I
) TRIP (I
) RESISTANCE SWITCH SIZE (D) MAX. CERA-MITE
CURRENT CURRENT R
TOL. TEMP. NOMINAL VOLTAGE PART
mA mA Ohms %
°
C mm V
RMS
NUMBER
70 140 100 25 120 6.5 265 307C1418
100 200 20 20 80 8 220 307C1305
100 200 30 20 105 8 220 307C1506
110 220 18 20 80 8 220 307C1354
110 220 25 20 105 8 220 307C1514
120 240 15 20 80 8 220 307C1129
120 240 20 20 105 8 220 307C1296
120 240 25 20 120 8 220 307C1470
130 260 13 20 80 8 120 307C1421
120 240 39 30 120 8.7 250 307C1505
120 240 25 25 105 8.7 250 307C1501
150 300 12 20 90 8.7 110 307C1439
120 240 15 25 80 9.5 220 307C1465
125 250 20 20 105 9.5 220 307C1507
135 270 10 25 80 9.5 220 307C1469
150 300 10 20 105 9.5 220 307C1233
170 340 10 20 105 11.2 220 307C1234
110 220 23 20 80 14.5 300 307C1262
125 250 18 25 80 14.5 265 307C1254
Note 1 Note 2 Note 3
CUSTOM PTCR PELLET
DESIGN CAPABILITY
Vishay Cera-Mite will customize
solid state overcurrent protector
PTCRs to your exact requirements
for telecommunication, power
supply, or general electronic
use. Providing great flexibility to
establish specific voltage, hold
current, time-trip characteristic, and
ambient temperature values.
Each device must be evaluated
and ratings established per appli-
cation. Mechanical packaging
influences performance ratings.
Table 3
RATING CHART FOR CUSTOM PELLETS
DISC DIAMETER (2.5mm THICK) 6.5mm 8mm 9.5mm 11mm 12.5mm 14.5mm
Continuous Voltage Rating (rms)
(proportional to resistance) 100
–
300 100
–
300100
–
300 100
–
300 100
–
300 50 - 300
Resistance Range @ 25
°
C (ohms) 10 to 35 7 to 25 5 to 20 4 to 17 2 to 15 1 to 10
Continuous Carry Current (mA)
Ambient 25
°
to 50
°
C (inversely 60
–
120 75
–
175 100
–
200 110
–
250 130
–
400 150
–
600
proportional to resistance)
Approximate Minimum Power
to Trip or Reset (watts) 0.4 0.5 0.6 0.7 0.8 0.9
Interrupting Capability
A. Repetitive (25 to 300 V
RMS
)
Peak power in watts 600 700 800 900 1000 1100
B. Non-repetitive (for 10 ohm
pellet) I
2
t Let Through 2.5 4.0 7.5 15 20 30
Maximum Safe Interrupting
Voltage (rms) (voltage rating 300 350 400 450 500 600
is proportional to resistance)
Fig P-11
WIRE LEADED PTC
TELECOM THERMISTORS
Resettable current limiters featuring
hold current and voltage ratings for
telecommunication applications.
Fig P-12
TELECOM CURRENT LIMITERS
Rated Voltage = 60Vdc; Rated Current = 3A at rated voltage.
Note 1
Hold and trip
currents specified at
25
°
C ambient.
Note 2
R25 is nominal zero
power resistance
(± 25%) at 25
°
C.
Note 3
P/N suffix describes
options including:
Tape & Reel
Wire Size
Wire Style &
Length
Lead Spacing
Coating Material
D
32mm min
4max
LS = 5mm
5mm
max
Tinned Copper Wire
22 AWG Standard
20 AWG on D=14.5mm
Pass-Thru Pulse
PTCR
1000
10 x 1000μ sec.
± 1000V peak
Rating applies to pellets with silver electrodes and pressure connections.
TRANSIENT VOLTAGE &
CURRENT
Because of the thermal storage
capacity of the ceramic PTCR,
transient surges do not cause tripping.
The PTCR is considered to be
transparent to these low energy
transients.
Fig P-11
shows a typical
test circuit for such transients.
Table 4