參數資料
型號： 363D
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 測量放大器
英文描述： LM363 Precision Instrumentation Amplifier
中文描述： INSTRUMENTATION AMPLIFIER, 3000 uV OFFSET-MAX, CDIP16
封裝： HERMETIC SEALED, DIP-16
文件頁數： 13/22頁
文件大小： 452K
代理商： 363D
Application Hints
(Continued)
Because the LM363’s output voltage is approximately one
diode drop below the voltage at pin 15 (pin 8 for the 8-pin
device), this point may be used to limit output swing as seen
inFigure 7a. Current available from this pin is only 50
m
A, so
that zeners must have a sharp breakdown to clamp accu-
rately. Alternatively, a diode tied to a voltage source could
be used as in Figure 7b.
TL/H/5609–15
FIGURE 7. Output Clamp
SHIELD DRIVERS
When differential signals are sent through long cables, three
problems occur. First, noise, both common-mode and differ-
ential, is picked up. Second, signal bandwidth is reduced by
the RC low-pass filter formed by the source impedance and
the cable capacitance. Finally, when these RC time con-
stants are not identical (unbalanced source impedance
and/or unbalanced capacitance), AC common-mode rejec-
tion is degraded, amplifying both induced noise and
‘‘ground’’ noise. Either filtering at the amplifier inputs or
slowing down the amplifier by overcompensating will indeed
reduce the noise, but the price is slower response. The
LM363D’s dual shield drivers can actually increase band-
width while reducing noise.
The way this is done is by bootstrapping out shield capaci-
tance. The shield drivers follow the input signal. Since both
sides of the shield capacitance swing the same amount, it is
effectively out of the circuit at frequencies of interest.
Hence, the input signal is not rolled off and AC CMRR is not
degraded (Figure 8). The LM363D’s shield drivers can han-
dle capacitances (shield to center conductor) as high as
1000 pF with source resistances up to 100 k
X
.
For best results, identical shielded cables should be used
for both signal inputs, although small mismatches in shield
driver to ground capacitance (
s
500 pF) do not cause prob-
lems. At certain low values of cable capacitance (50 pF–
200 pF), high frequency oscillations can occur at high
source resistance (
t
10 k
X
). This is alleviated by adding
50 pF to ground at both shield driver outputs. Do not use
only one shield driver for a single-ended signal as oscilla-
tions can result; shield driver to input capacitance must be
roughly balanced (
g
30%). To further reduce noise pickup,
the shielded signal lines may be enclosed together in a
grounded shield. If a large amount of RF noise is the prob-
lem, the only sure cure is a filter capacitor at both inputs;
otherwise the RFI may be internally rectified, producing an
offset.
DC loading on the shield drivers should be minimized. The
drivers can only source approximately 40
m
A; above this
value the input stage bias voltages change, degrading V
OS
and CMRR. While the shield drivers can sink several mA,
V
OS
may degrade severely at loads above 100
m
A (see
Shield Driver Loading Error curve in Typical Performance
Characteristics). Because the shield drivers are one diode
drop above the input levels, unbalanced leakage paths from
shield to input can produce an input offset at high source
impedances. Buffering with emitter-followers (Figure 8b) re-
duces this leakage current by reducing the voltage differen-
tial and eliminates any loading on the amplifier.
TL/H/5609–16
FIGURE 8. Driving Shielded Cables
MISCELLANEOUS TRIMMING
The V
OS
adjust and shield driver pins available on the 16-
pin package may be used to trim the other parameters be-
sides offset voltage, as illustrated inFigure 10. The bias-cur-
rent trim relies on the fact that the voltage on the shield
driver and gain setting pins is one diode drop respectively
above and below the input voltage. Input bias current can
be held to within 100 pA over the entire common-mode
range, and input offset current always stays under 30 pA.
The CMRR trims use the shield driver pins to drive the V
OS
adjust pins, thus maintaining the LM363’s ultra-high input
impedance.
13
相關PDF資料
PDF描述
36401E2N2A INDUCTOR SMD 2.2NH
36401E3N3A INDUCTOR SMD 3.3NH
368-95 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
368H205 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
369A-13 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS
相關代理商/技術參數
參數描述
363D353U040W4C 制造商:Sprague/Vishay 功能描述:CGC040X335C NOTES
363I-5INXNH-P150F 制造商:3M Electronic Products Division 功能描述:60010007981
363I-DISC-5IN-60F 制造商:3M Electronic Products Division 功能描述:60010007866 5 X NH 60F 363I
363L-DISC-5IN-80MIC 制造商:3M Electronic Products Division 功能描述:60440107419 5XNH
363M100K 制造商:HONEYWELL CLAROSTAT 功能描述:Res Cermet Trimmer 100K Ohm 10% 1/2W 1Turn 3.81mm (9.53 X 9.53 X 4.83mm) Pin Thru-Hole
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*