參數資料
型號: 37B77X
廠商: SMSC Corporation
英文描述: ENHANCED SUPER I/O CONTROLLER WITH WAKE UP FEATURES
中文描述: 增強型超I / O與向上特征喚醒控制器
文件頁數: 37/196頁
文件大?。?/td> 573K
代理商: 37B77X
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁
131
CONFIGURATION
The Configuration of the FDC37B77x is very
flexible and is based on the configuration
architecture implemented in typical Plug-and-
Play components. The FDC37B77x is designed
for
motherboard
applications
in
which
the
resources required by their components are
known.
With its flexible resource allocation
architecture, the FDC37B77x allows the BIOS to
assign resources at POST.
SYSTEM ELEMENTS
Primary Configuration Address Decoder
After a hard reset (RESET_DRV pin asserted) or
Vcc Power On Reset the FDC37B77x is in the
Run Mode with all logical devices disabled. The
logical devices may be configured through two
standard Configuration I/O Ports
(INDEX and
DATA)
by
placing
the
FDC37B77x
into
Configuration Mode.
The BIOS uses these
configuration
ports
to
initialize
the
logical
devices at POST. The INDEX and DATA ports
are only valid when the FDC37B77x is in
Configuration Mode.
The SYSOPT pin is latched on the falling edge
of the RESET_DRV or on Vcc Power On Reset
to determine the configuration register's base
address. The SYSOPT pin is used to select the
CONFIG PORT's I/O address at power-up.
Once powered up the configuration port base
address can be changed through configuration
registers CR26 and CR27. The SYSOPT pin is
a hardware configuration pin which is shared
with the nRTS1 signal on pin 87. During reset
this pin is a weak active low signal which sinks
30A. Note: All I/O addresses are qualified with
AEN.
The INDEX and DATA ports are effective only
when the chip is in the Configuration State.
PORT NAME
SYSOPT= 0
PULL-DOWN RESISTOR
(NOTE 1)
SYSOPT= 1
10K PULL-UP
RESISTOR
TYPE
CONFIG PORT (Note
2)
0x03F0
0x0370
Write
INDEX PORT (Note 2)
0x03F0
0x0370
Read/Write
DATA PORT
INDEX PORT + 1
Read/Write
Note 1:
If using TTL RS232 drivers use 1K pull-down. If using CMOS RS232 drivers use
10K pull-down.
Note 2:
The configuration port base address can be relocated through CR26 and CR27.
Entering the Configuration State
The device enters the Configuration State when
the following Config Key is successfully written
to the CONFIG PORT.
Config Key = < 0x55 >
Exiting the Configuration State
The device exits the Configuration State when
the following Config Key is successfully written
to the CONFIG PORT.
Config Key = < 0xAA>
相關PDF資料
PDF描述
37C669 DIODE SCHOTTKY SINGLE 25V 200mW 0.5V-vf 200mA-IFM 30mA-IF 2uA-IR SOD-323 3K/REEL
37C672 ENHANCED SUPER I/O CONTROLLER WITH FAST IR
37C67X ENHANCED SUPER I/O CONTROLLER WITH FAST IR
37C957FR ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS
37FMA1-ABW31N SPECIAL SWITCH-PIEZO SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT-THREADED
相關代理商/技術參數
參數描述
37B999 制造商:TE Connectivity 功能描述:
37BCB34-4 制造商: 功能描述: 制造商:undefined 功能描述:
37BK 功能描述:烙鐵 Weller Modular Heatr Thread-on Tips 50W RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included
37BMA-SMA-50-1 制造商:HUBER+SUHNER 功能描述:BETWEEN SERIES ADAPTER
37BNC-50-0-1/3E 制造商:HUBER+SUHNER 功能描述:BETWEEN SERIES ADAPTER