- 您現在的位置：買賣IC網 > PDF目錄50127 > 44MPA0478 (MIMIX BROADBAND INC) 43.5-46.5 GHz GaAs MMIC Power Amplifier PDF資料下載
參數資料
| 型號： | 44MPA0478 |
| 廠商： | MIMIX BROADBAND INC |
| 元件分類： | 放大器 |
| 英文描述： | 43.5-46.5 GHz GaAs MMIC Power Amplifier |
| 中文描述： | 43500 MHz - 46500 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| 封裝： | DIE-14 |
| 文件頁數： | 4/5頁 |
| 文件大?。?/td> | 434K |
| 代理商： | 44MPA0478 |
Pre-production
App Note [1] Biasing
- It is recommended to separately bias each amplifier stage Vd1 through Vd3 at Vd(1,2,3)=5.0V with Id1=Id2=360mA, and
Id3=720mA. Separate biasing is recommended if the amplifier is to be used at high levels of saturation, where gate rectification will alter the
effective gate control voltage. For non-critical applications it is possible to parallel all stages and adjust the common gate voltage for a total drain
current Id(total)=1440 mA. It is also recommended to use active biasing to keep the currents constant as the RF power and temperature vary; this
gives the most reproducible results. Depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a
single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. The gate of
the pHEMT is controlled to maintain correct drain current and thus drain voltage. The typical gate voltage needed to do this is -0.5V. Typically the
gate is protected with Silicon diodes to limit the applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is
available before applying the positive drain supply.
App Note [2] Bias Arrangement
-
For Parallel Stage Bias (Recommended for general applications) -- The same as Individual Stage Bias but all the drain or gate pad DC bypass
capacitors (~100-200 pf ) can be combined. Additional DC bypass capacitance (~0.01 uF) is also recommended to all DC or combination (if gate or
drains are tied together) of DC bias pads. All DC pads have been tied together on chip and can be biased from either side.
For Individual Stage Bias (Recommended for saturated applications) -- Each DC pad (Vd1,2,3 and Vg1,2,3) needs to have DC bypass capacitance
(~100-200 pf ) as close to the device as possible. Additional DC bypass capacitance (~0.01 uF) is also recommended. All DC pads have been tied
together on chip and can be biased from either side.
MTTFTables (TBD)
These numbers were calculated based on accelerated life test information and thermal model analysis received from the fabricating foundry.
43.5-46.5 GHz GaAs MMIC
Power Amplifier
Page 4 of 5
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice.
2005 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
44MPA0478
Bias Conditions:
Vd=5V, Id1=Id2=360 mA, Id3=720 mA
1
2
3
R=20 Ohm
1
2
3
R=16 Ohm
R=20 Ohm
R=15 O hm
R=20 Ohm
1
2
3
1
2
3
R=16 Ohm
R= 16 Ohm
R=15 Ohm
R=16 O hm
1
2
3
1
2
3
1
2
3
1
2
3
R=16 Ohm
R=15 O hm
R=16 Ohm
R=20 O hm
R= 20 Ohm
R= 16 Ohm
R=15 Ohm
R=20 O hm
R=16 Ohm
12
3
4
R =50 Ohm
1
2
3
4
R=50 O hm
VG1 A
V D1A
VG2A
VD2 A
VG3 A
VD3 A
RFIN
RF OU T
VG1 B
V D1B
VG2B
VD2 B
VG3 B
VD3 B
Device Schematic
Backplate
Temperature
55 deg Celsius
75 deg Celsius
95 deg Celsius
Channel
Temperature
165.2 deg Celsius
191.4 deg Celsius
217.1 deg Celsius
FITs
2.74E+02
2.57E+03
9.13E+03
MTTF Hours
3.65E+06
3.89E+05
5.48E+04
Rth
78.5 C/W
82.8 C/W
87.0 C/W
April 2005 - Rev 01-Apr-05
相關PDF資料 |
PDF描述 |
|---|---|
| 44 | |
| 450-10-216-00-006 | External Plug-In Power Supply; Series:FW50; Output Voltage:12V; Output Power Max:50W; Output Current:4.15A; No. of Outputs:1; Input Current:4.15A; Leaded Process Compatible:Yes; Size:127 x 33 x 76.2 mm; Supply Voltage Max:240VAC RoHS Compliant: Yes |
| 450-10-216-00-106 | External Plug-In Power Supply; Series:FW50; Output Voltage:12V; Output Power Max:50W; Output Current:4.15A; No. of Outputs:1; Input Current:4.15A; Leaded Process Compatible:Yes; Size:127 x 33 x 76.2 mm; Supply Voltage Max:240VAC RoHS Compliant: Yes |
| 450-10-216-00-001 | PT 26C 26#20 SKT RECP |
| 450-1800-01-03-00 | COPPER ALLOY, GOLD FINISH, PCB TERMINAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 44MS30-01-1-02N | 制造商:Grayhill 功能描述:SWIT ROTARY SP 2 SHAFT SLDR LUG 5A 115VAC 30VDC - Bulk 制造商:Grayhill 功能描述:Switch Rotary SPDT 2 Flatted Shaft Solder Lug 1A 115VAC 115VDC |
| 44MS30-01-1-03N | 制造商:Grayhill 功能描述:SWIT ROTARY SP 3 SHAFT SLDR LUG 5A 115VAC 30VDC - Bulk 制造商:Grayhill 功能描述:Switch Rotary SP3T 3 Flatted Shaft Solder Lug 1A 115VAC 115VDC |
| 44MS30-01-1-04N | 制造商:Grayhill 功能描述:Switch Rotary SP4T 4 Flatted Shaft Solder Lug 1A 115VAC 115VDC |
| 44MS30-01-1-04NC | 制造商:Grayhill 功能描述:SWIT ROTARY SP 4 SHAFT SLDR LUG 5A 115VAC 30VDC - Bulk |
| 44MS30-01-1-05N | 制造商:Grayhill 功能描述:SWIT ROTARY SP 5 SHAFT SLDR LUG 5A 115VAC 30VDC - Bulk 制造商:Grayhill 功能描述:Switch Rotary SP5T 5 Flatted Shaft Solder Lug 1A 115VAC 115VDC |
發布緊急采購，3分鐘左右您將得到回復。