參數資料
型號: 514KAAXXXXXXBAG
廠商: SILICON LABORATORIES
元件分類: 時鐘產生/分配
英文描述: 250 MHz, OTHER CLOCK GENERATOR, PDSO6
封裝: 3.20 X 5 MM, ROHS COMPLIANT PACKAGE-6
文件頁數: 3/32頁
文件大小: 267K
代理商: 514KAAXXXXXXBAG
Si514
Preliminary Rev. 0.9
11
e. Register 9 = 0x09 (M_Int[8:3])
f. M_Int = 0b001001010 = 0x4A = 0d74
g. M_Frac = 0x097C65D3 = 159,147,475
h. M= M_Int + M_Frac/229 = 74 + 159,147,475/229 = 74.296435272321105
2. Calculate Mnew:
a. Mnew = 74.296435272321105 x 148.352/148.5 = 74.2223889933965
b. M_Intnew = 74 = 0x4A
c. M_Fracnew = 0.2223889933965 x 229 = 119,394,181 = 0x071DCF85
3. Write Mnew to Registers 5-7:
a. Register 5 = 0x85
b. Register 6 = 0xCF
c. Register 7 = 0x1D
4. Write Mnew to Register 8:
a. Register 8 = 0x47
5. Write Mnew to Register 9:
a. Register 9 = 0x09
2.3. Programming a Large Frequency Change (> ±1000 ppm)
Large frequency changes are those that vary the FVCO frequency by an amount greater than ±1000 ppm from an
operating FCENTER. Figure 2 illustrates the difference between large and small frequency changes. Changing from
FCENTER to F'CENTER requires a calibration cycle that resets internal circuitry to establish F'CENTER as the new
operating center frequency. The below steps are recommended when performing large frequency changes:
1. Disable the output: Write OE register bit to a 0 (Register 132, bit2)
2. If using one of the standard frequencies listed in Table 9, then write the new LP1, LP2, M_Frac, M_Int, HS_DIV
and LS_DIV register values according to the table (be sure to write M_Int[8:3] (Register 9) after writing to the
M_Frac registers (Registers 5-8)). Skip to Step 9. If the desired frequency is not in the table, then follow steps
4-8 below.
3. Determine the minimum value of LS_DIV (minimizing LS_DIV minimizes the number of dividers on the output
stage, thus minimizing jitter) according to the following formula:
a. LS_DIV = FVCO(MIN)/(FOUT x HS_DIV(MAX)) (Eq 2.6)
b. LS_DIV = 2080/(FOUT(MHz) x 1022) (Eq 2.7)
i. Since LS_DIV is restricted to: dividing by 1,2,4,8,16,32, choose the next largest value over the
result derived in Eq 2.7 (e.g., if result is 4.135, choose LS_DIV = 8)
4. Determine the minimum value for HS_DIV (this optimizes timing margins)
a. HS_DIV(MIN) = FVCO(MIN)/(FOUT x LS_DIV) (Eq 2.8)
b. HS_DIV(MIN) = 2080/(FOUT(MHz) x LS_DIV) (Eq 2.9)
i.HS_DIV(MIN) will be the next even number greater than or equal to the result derived in Eq 2.9
(keeping in the range of 10-1022)
Note:
SPEED_GRADE_MIN (Reg 48) ≤ LS_DIV x HS_DIV ≤ SPEED_GRADE_MAX (Reg 49); If outside this range, the output
will be forced to the disabled state.
5. Determine a value for M according to the following formula (all values are in decimal format):
a. M = LS_DIV x HS_DIV x FOUT/FXO (Eq 2.10)
b. M = LS_DIV x HS_DIV x FOUT(MHz)/31.98 (Eq 2.11)
c. M_Int = INT[M] (Eq 2.12)
d. M_Frac = (M – INT[M]) x 229 (Eq 2.13)
相關PDF資料
PDF描述
514KABXXXXXXBAG 170 MHz, OTHER CLOCK GENERATOR, PDSO6
514KBAXXXXXXBAGR 250 MHz, OTHER CLOCK GENERATOR, PDSO6
514KBBXXXXXXAAGR 170 MHz, OTHER CLOCK GENERATOR, PDSO6
514KBCXXXXXXAAG 125 MHz, OTHER CLOCK GENERATOR, PDSO6
514KCBXXXXXXAAGR 170 MHz, OTHER CLOCK GENERATOR, PDSO6
相關代理商/技術參數
參數描述
514KCB000817BAG 功能描述:標準時鐘振蕩器 PROGRMABLE XO 6 PIN 0.7PS RS JTR RoHS:否 制造商:AVX 產品:Standard Clock Oscillators 封裝 / 箱體:7 mm x 5 mm 頻率:75 MHz 頻率穩定性:50 PPM 電源電壓:2.5 V 負載電容: 端接類型:SMD/SMT 最小工作溫度:0 C 最大工作溫度:+ 70 C 輸出格式:LVDS 尺寸: 封裝:Reel 系列:
514KCB000942BAG 功能描述:標準時鐘振蕩器 PROGRMABLE XO 6 PIN 0.7PS RS JTR RoHS:否 制造商:AVX 產品:Standard Clock Oscillators 封裝 / 箱體:7 mm x 5 mm 頻率:75 MHz 頻率穩定性:50 PPM 電源電壓:2.5 V 負載電容: 端接類型:SMD/SMT 最小工作溫度:0 C 最大工作溫度:+ 70 C 輸出格式:LVDS 尺寸: 封裝:Reel 系列:
514L3 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Infrared Emitting Diodes (IRED)
514MAA000148AAG 制造商:Silicon Laboratories Inc 功能描述:OSCILLATOR - Trays
514MAA000881AAG 制造商:Silicon Laboratories Inc 功能描述:OSCILLATOR - Trays