參數資料
型號: 5962-88650012X
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: ADC
英文描述: 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, CQCC20
封裝: CERAMIC, LCC-20
文件頁數: 4/17頁
文件大小: 227K
代理商: 5962-88650012X
MAX4814E
For example: If AD0, AD1, and AD2 are hardwired to
ground, then the complete address is 0111000. The full
address is defined as the seven most significant bits
followed by the read/write bit. Set the read/write bit to 1
to configure the MAX4814E to read mode. Set the
read/write bit to 0 to configure the MAX4814E to write
mode. The address is the first byte of information sent
to the MAX4814E after the START condition.
.
Applications Information
ESD Protection
As with all Maxim devices, ESD-protection structures
are incorporated on all pins to protect against electro-
static discharges encountered during handling and
assembly. Switch A, switch B, and switch SW_ are fur-
ther protected against static electricity. Maxim’s engi-
neers have developed state-of-the-art structures to
protect these pins against ESD up to ±6kV without
damage. The ESD structures withstand high ESD in
normal operation, and when the device is powered
down. ESD protection can be tested in various ways.
The ESD protection of switch A, switch B, and switch
SW_ are characterized for ±6kV (Human Body Model)
using the MIL-STD-883.
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, test methodology, and test results.
Human Body Model
Figure 7 shows the Human Body Model, and Figure 8
shows the current waveform it generates when dis-
charged into a low impedance. This model consists of a
100pF capacitor charged to the ESD voltage of interest
that is then discharged into the test device through a
1.5kΩ resistor.
DVI/HDMI 2:4 Low-Frequency Fanout Switch
12
______________________________________________________________________________________
Table 4. I2C Register R1 (0X01) to DO_ Mapping
PIN
REGISTER R1 (0x01)
MODE
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
OUTPUT PIN
CONFIGURATION
1
0
DO0
0
1
0
1
DO0
1
1
X
DO0
Hi-Z
1—
0
0—
DO1
0
1—
0
1—
DO1
1
1
X
DO1
Hi-Z
1—
—0
0—
DO2
0
1—
—0
1—
DO2
1
1
X
DO2
Hi-Z
100
DO3
0
101
DO3
1
X
DO3
Hi-Z
Table 5. I2C Register R0 (0x00)
REGISTER R0 (0x00)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
BBEN
BBSEL1
BBSEL0
BAEN
BASEL1
BASEL0
X
X = Hardwired, not programmed by user.
X = Don’t care.
相關PDF資料
PDF描述
5962-8865002RX 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, CDIP20
5962-8865001RX 1-CH 8-BIT FLASH METHOD ADC, PARALLEL ACCESS, CDIP20
5962-8868503PA 1-CHANNEL POWER SUPPLY SUPPORT CKT, CDIP8
5962-8868503HA 1-CHANNEL POWER SUPPLY SUPPORT CKT, CDFP10
5962-88685032A 1-CHANNEL POWER SUPPLY SUPPORT CKT, CQCC20
相關代理商/技術參數
參數描述
5962-8865001RA 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
5962-88650022A 功能描述:模數轉換器 - ADC IC 8-BIT CMOS RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
5962-88650022C 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
5962-8865002RA 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
5962-8865101RA 制造商:Integrated Device Technology Inc 功能描述: