- 您現在的位置：買賣IC網 > PDF目錄67329 > 5962-8990502EA (TEXAS INSTRUMENTS INC) 2.2 A SWITCHING CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, CDIP16 PDF資料下載
參數資料
| 型號： | 5962-8990502EA |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 2.2 A SWITCHING CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, CDIP16 |
| 封裝： | CERAMIC, DIP-16 |
| 文件頁數： | 16/18頁 |
| 文件大小： | 477K |
| 代理商： | 5962-8990502EA |
UC1823A,UC2823A, UC2823B,
UC3823A,UC3823B,UC1825A,
UC2825A,UC2825B,UC3825A,UC3825B
SLUS334D AUGUST 1995 REVISED NOVEMBER 2008
www.ti.com
7
LEADING EDGE BLANKING
The UC3823A, UC2823B, UC3825A, and UC3825B perform fixed frequency pulse width modulation control. The
UC3823A, and UC3823B outputs operate together at the switching frequency and can vary from zero to some value less
than 100%. The UC3825A and UC3825B outputs are alternately controlled. During every other cycle, one output is off.
Each output then switches at one-half the oscillator frequency, varying in duty cycle from 0 to less than 50%.
To limit maximum duty cycle, the internal clock pulse blanks both outputs low during the discharge time of the oscillator.
On the falling edge of the clock, the appropriate output(s) is driven high. The end of the pulse is controlled by the PWM
comparator, current limit comparator, or the overcurrent comparator.
Normally the PWM comparator senses a ramp crossing a control voltage (error amplifier output) and terminates the pulse.
Leading edge blanking (LEB) causes the PWM comparator to be ignored for a fixed amount of time after the start of the
pulse. This allows noise inherent with switched mode power conversion to be rejected. The PWM ramp input may not
require any filtering as result of leading edge blanking.
To program a leading edge blanking (LEB) period, connect a capacitor, C, to CLK/LEB. The discharge time set by C and
the internal 10-k
resistor determines the blanked interval. The 10-k resistor has a 10% tolerance. For more accuracy,
an external 2-k
1% resistor (R) can be added, resulting in an equivalent resistance of 1.66 k with a tolerance of 2.4%.
The design equation is:
t
LEB + 0.5
R
10 kW
C
Values of R less than 2 k
should not be used.
Leading edge blanking is also applied to the current limit comparator. After LEB, if the ILIM pin exceeds the 1-V threshold,
the pulse is terminated. The overcurrent comparator, however, is not blanked. It catches catastrophic overcurrent faults
without a blanking delay. Any time the ILIM pin exceeds 1.2 V, the fault latch is set and the outputs driven low. For this
reason, some noise filtering may be required on the ILIM pin.
UDG95105
Figure 4. Leading Edge Blanking Operational Waveforms
(2)
相關PDF資料 |
PDF描述 |
|---|---|
| 5962-87681022A | 2.2 A SWITCHING CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, CQCC20 |
| 5962-8768103XA | 2.2 A SWITCHING CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, BCY28 |
| 5962-8768102EA | 2.2 A SWITCHING CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, CDIP16 |
| 5962-89920022A | 0.4 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, CQCC20 |
| 5962-8992002VA | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, CDIP18 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 5962-8991501UA | 制造商:Microsemi Corporation 功能描述:5962-8991501UA - Rail/Tube |
| 5962-8992001VX | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 5962-89920022A | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| 59628992501EA | 制造商:TI 功能描述:SNJ54LS378J |
| 5962-8992501EA | 制造商:Texas Instruments 功能描述:Flip Flop D-Type Bus Interface Pos-Edge 1-Element 16-Pin CDIP Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:FLIP FLOP D-TYPE BUS INTRFC POS-EDGE 1-ELEM 16CDIP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。