參數資料
型號: 5962-9957701NXD
廠商: TEXAS INSTRUMENTS INC
元件分類: ADC
英文描述: 4-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO32
封裝: GREEN, PLASTIC, TSSOP-32
文件頁數: 18/43頁
文件大小: 426K
代理商: 5962-9957701NXD
THS1206
SLAS217H – MAY 1999 – REVISED JULY 2003#
www.ti.com
25
ADC CONTROL REGISTERS
Control Register 0 (see Table 8)
BIT 11
BIT 10
BIT 9
BIT 8
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0
TEST1
TEST0
SCAN
DIFF1
DIFF0
CHSEL1
CHSEL0
PD
MODE
VREF
Table 9. Control Register 0 Bit Functions
BITS
RESET
VALUE
NAME
FUNCTION
0
VREF
Vref select:
Bit 0 = 0
→ The internal reference is selected
Bit 0 = 1
→ The external reference voltage is selected
1
0
MODE
Continuous conversion mode/single conversion mode
Bit 1 = 0
→ Continuous conversion mode is selected
An external clock signal is applied to the CONV_CLK input in this mode. With every falling edge of the
CONV_CLK signal a new converted value is written into the FIFO.
Bit 1 = 1
→ Single conversion mode is selected
In this mode, the CONV_CLK input functions as a CONVST input. A single conversion is initiated on the
THS1206 by pulsing the CONVST input. On the falling edge of CONVST, the sample and hold stages of the
selected analog inputs are placed into hold simultaneously, and the conversion sequence for the selected
channels is started. The signal DATA_AV (data available) becomes active when the trigger condition is
satisfied.
2
0
PD
Power down.
Bit 2 = 0
→ The ADC is active
Bit 2 = 1
→ Power down
The reading and writing to and from the digital outputs is possible during power down. It is also possible to
read out the FIFO.
3, 4
0,0
CHSEL0,
CHSEL1
Channel select
Bit 3 and bit 4 select the analog input channel of the ADC. Refer to Table 10.
5,6
1,0
DIFF0, DIFF1
Number of differential channels
Bit 5 and bit 6 contain information about the number of selected differential channels. Refer to Table 10.
7
0
SCAN
Autoscan enable
Bit 7 enables or disables the autoscan function of the ADC. Refer to Table 10.
8,9
0,0
TEST0,
TEST1
Test input enable
Bit 8 and bit 9 control the test function of the ADC. Three different test voltages can be measured. This
feedback allows the check of all hardware connections and the ADC operation.
Refer to Table 11 for selection of the three different test voltages. The control signal DATA_AV is disabled in
the test mode. Test voltage readings have to be done independent from DATA_AV. To get the THS1206 back
to the normal operating mode, apply the the initialization routine.
相關PDF資料
PDF描述
5962-9958302Q2A 0.1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, CQCC20
5962-9958301Q2A 0.1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, CQCC20
5962-9958302QPA 0.1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, CDIP8
TL5001AIP 0.1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8
TL5001AIPE4 0.1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8
相關代理商/技術參數
參數描述
5962-9958101QXC 功能描述:LVDS 接口集成電路 RoHS:否 制造商:Texas Instruments 激勵器數量:4 接收機數量:4 數據速率:155.5 Mbps 工作電源電壓:5 V 最大功率耗散:1025 mW 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-16 Narrow 封裝:Reel
5962-9958301Q2A 制造商:Texas Instruments 功能描述:DC DC Cntrlr Single-OUT PWM DC to DC Controller 3.6V to 40V Input 20-Pin LCCC Tube
5962-9958301QPA 制造商:Texas Instruments 功能描述:DC DC Cntrlr Single-OUT PWM DC to DC Controller 3.6V to 40V Input 8-Pin CDIP Tube
5962-9958302Q2A 制造商:Texas Instruments 功能描述:DC DC Cntrlr Single-OUT PWM DC to DC Controller 3.6V to 40V Input 20-Pin LCCC Tube
5962-9958302QPA 制造商:Texas Instruments 功能描述:DC DC Cntrlr Single-OUT PWM DC to DC Controller 3.6V to 40V Input 8-Pin CDIP Tube