參數資料
型號: 73S1209F-68IM/F
廠商: TERIDIAN SEMICONDUCTOR CORP
元件分類: 電源管理
英文描述: POWER SUPPLY MANAGEMENT CKT, QCC68
封裝: LEAD FREE, QFN-68
文件頁數: 115/123頁
文件大?。?/td> 1385K
代理商: 73S1209F-68IM/F
DS_1209F_004
73S1209F Data Sheet
Rev. 1.2
91
Protocol Mode Register (SPrtcol): 0xFE0D
0x03
This register determines the protocol to be use when communicating with the selected smart card. This
register should be updated as required when switching between smart card interfaces.
Table 86: The SPrtcol Register
MSB
LSB
SCISYN
MOD9/8B SCESYN
0
TMODE
CRCEN
CRCMS RCVATR
Bit
Symbol
Function
SPrtcol.7
SCISYN
Smart Card Internal Synchronous mode – Configures internal smart card
interface for synchronous mode. This mode routes the internal interface
buffers for RST, IO, C4, C8 to SCCtl register bits for direct firmware control.
CLK is generated by the ETU counter.
SPrtcol.6
MOD9/8B
Synchronous 8/9 bit mode select – For sync mode, in protocols with 9-bit
words, set this bit. The first eight bits read go into the RX FIFO and the
ninth bit read will be stored in the IO (or SIO) data bit of the SRXCtl
register.
SPrtcol.5
SCESYN
Smart Card External Synchronous mode – Configures External Smart Card
interface for synchronous mode. This mode routes the external smart card
interface buffers for SIO to SCECtl register bits for direct firmware control.
SCLK is generated by the ETU counter.
SPrtcol.4
0
Reserved bit, must always be set to 0.
SPrtcol.3
TMODE
Protocol mode select – 0: T=0, 1: T=1. Determines which smart card
protocol is to be used during message processing.
SPrtcol.2
CRCEN
CRC Enable – 1 = Enabled, 0 = Disabled. Enables the
checking/generation of CRC/LRC while in T=1 mode. Has no effect in T=0
mode. If enabled and a message is being transmitted to the smart card,
the CRC/LRC will be inserted into the message stream after the last TX
byte is transmitted to the smart card. If enabled, CRC/LRC will be checked
on incoming messages and the value made available to the firmware via
the CRC LS/MS registers.
SPrtcol.1
CRCMS
CRC Mode Select - 1 = CRC, 0 = LRC. Determines type of checking
algorithm to be used.
SPrtcol.0
RCVATR
Receive ATR – 1 = Enable ATR timeout, 0 = Disable ATR timeout. Set by
firmware after the smart card has been turned on and the hardware is
expecting ATR.
相關PDF資料
PDF描述
73S1209F-44IMR/F POWER SUPPLY MANAGEMENT CKT, QCC44
73S1209F-44IM/F POWER SUPPLY MANAGEMENT CKT, QCC44
73S1210F-44IMR/F 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC44
73S1210F-68IM/F/P 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68
73S1210F-44IMR/F/P 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC44
相關代理商/技術參數
參數描述
73S1209F-68IMR/F 功能描述:8位微控制器 -MCU Contained 80515-SoC Serial Hst Interface RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
73S1209F-68IMR/F/P 功能描述:IC SMART CARD READER PROG 68-QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:73S12xx 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C,智能卡,UART/USART,USB 外圍設備:LED,POR,WDT 輸入/輸出數:9 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件
73S1209F-68M/F/P1 功能描述:8位微控制器 -MCU Contained 80515-SoC Serial Hst Interface RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
73S1209F-EB 功能描述:開發板和工具包 - 8051 73S1209F Eval Brd (Doc. Cd, Cable) RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓:
73S1209F-IM44 DK 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 73S1209F Dev Kit Eval Bd Ice Cable Cd