- 您現在的位置：買賣IC網 > PDF目錄16278 > 73S8010C-DB (Maxim Integrated Products)BOARD DEMO 73S8010C 28-SOIC PDF資料下載
參數資料
| 型號： | 73S8010C-DB |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 26/27頁 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO 73S8010C 28-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁
73S8010C Data Sheet
DS_8010C_024
8
Rev. 1.5
ACK bit is sent to the master by the device. The master should send the STOP condition after receiving
the ACK bit.
Figure 2: I
2C Bus Write Protocol
2.2
Host Interface Status
Table 3 describes the Host Interface Status Register bits (power-on Reset = 0x04).
Table 3: Host Status Register
Name
Bit
Description
PRES
0
Set when the card is present; reset when the card is not present.
PRESL
1
Set when the PRES pin changes state (rising/falling edge); reset when the status
register is read. Generates an interrupt when set
I/O
2
Set when I/O is high; reset when I/O is low.
SUPL
3
Set when a voltage fault is detected; reset when the status register is read.
Generates an interrupt when set.
PROT
4
Set when an over-current or over-heating fault has occurred during a card session;
reset when the status register is read. Generates an interrupt when set.
MUTE
5
Set during ATR when the card has not answered during the ISO 7816-3 time
window (40000 card clock cycles); reset when the next session begins or this
register is read.
EARLY
6
Set during ATR when the card has answered before 400 card clock cycles; reset
when the next session begins or this register is read.
ACTIVE
7
Set when the card is active (VCC is on); reset when the card is inactive.
I
2C-bus Read from the Status Register:
The I
2C-bus Read Command from the Status Register follows the format shown in Figure 3.
After the START condition, the master sends a slave address. This address is seven bits long followed
by an eighth bit, which is the opcode bit (R/
W). A ‘one’ indicates the master will read data from the status
register. After the R/
W bit, the ’zero’ ACK bit is sent to the master by the device. The device now starts
sending the 8-bit status register data to the control register during the DATA bits time. After the DATA
bits, the ‘one’ ACK bit is sent to the device by the master. The master should send the STOP condition
after receiving the ACK bit.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP303LSN30T1G | IC DETECTOR VOLTAGE 3.0V 5TSOP |
| 73S8010R-DB | BOARD DEMO 73S8010R 28-SOIC |
| DD-DB1-AL202C-FB | DEV BD 20X2 LCD BLU TXT BLK BL |
| NCP301LSN30T1G | IC DETECTOR VOLTAGE 3.0V 5TSOP |
| DD-DB1-AL202C-FW | DEV BD 20X2 LCD WHT TXT BLK BL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8010C-IL/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-ILR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IM/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IM/F2 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IMR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發布緊急采購，3分鐘左右您將得到回復。