- 您現在的位置：買賣IC網 > PDF目錄16278 > 73S8010C-DB (Maxim Integrated Products)BOARD DEMO 73S8010C 28-SOIC PDF資料下載
參數資料
| 型號： | 73S8010C-DB |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DEMO 73S8010C 28-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
DS_8010C_024
73S8010C Data Sheet
Rev. 1.5
13
9
Deactivation Sequence
Deactivation is initiated either by the system controller resetting the Start/Stop bit, or automatically in the
event of hardware faults. Hardware faults are over-current, over-temperature, VDD fault, VCC fault, and
card extraction during the session.
The following steps and Figure 7 show the deactivation sequence and the timing of the card control
signals when the system controller clears the Start/Stop bit:
1. RST goes low at the end of t1.
2. CLK goes low at the end of t2.
3. I/O goes low at the end of t3. Out of reception mode.
4. Shut down VCC at the end of time t4.
Figure 7: Deactivation Sequence
10 Interrupt
The interrupt is an active low interrupt. It is set low if either a VCC fault or a VDD fault is detected. It is also
set low if one of the following status bit conditions is detected:
Early ATR
Mute ATR
Card insert or card extract
Protection status from Over-current or Over-heating
If the interrupt is set low by the detection of these status bits, then the interrupt is set high when these
status bits are read. (READ STATUS DONE)
Figure 8: FAULT Functions,
INT operation
t1 ≥ 0.5 μs
t3 ≥ 0.5 μs
t2 ≥ 7.5 μs
t4 ≥ 0.5 μs
INT
ANY FAULT
STATUS BITS
READ STATUS DONE
相關PDF資料 |
PDF描述 |
|---|---|
| NCP303LSN30T1G | IC DETECTOR VOLTAGE 3.0V 5TSOP |
| 73S8010R-DB | BOARD DEMO 73S8010R 28-SOIC |
| DD-DB1-AL202C-FB | DEV BD 20X2 LCD BLU TXT BLK BL |
| NCP301LSN30T1G | IC DETECTOR VOLTAGE 3.0V 5TSOP |
| DD-DB1-AL202C-FW | DEV BD 20X2 LCD WHT TXT BLK BL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8010C-IL/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-ILR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IM/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IM/F2 | 功能描述:I2C 接口集成電路 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| 73S8010C-IMR/F | 功能描述:I2C 接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發布緊急采購，3分鐘左右您將得到回復。