- 您現在的位置：買賣IC網 > PDF目錄358652 > 74HC21D SC70/µDFN, Single/Dual Low-Voltage, Low-Power µP Reset Circuits PDF資料下載
參數資料
| 型號： | 74HC21D |
| 英文描述： | SC70/µDFN, Single/Dual Low-Voltage, Low-Power µP Reset Circuits |
| 中文描述： | 雙4輸入與門 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 83K |
| 代理商： | 74HC21D |
2003 May 14
13
Philips Semiconductors
Product specification
Dual 2-input NOR gate
74HC2G02; 74HCT2G02
SOLDERING
Introduction to soldering surface mount packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certainsurfacemountICs,butitisnotsuitableforfinepitch
SMDs. In these situations reflow soldering is
recommended.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Driven by legislation and environmental forces the
worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 270
°
C depending on solder paste material. The
top-surface temperature of the packages should
preferably be kept:
below 220
°
C (SnPb process) or below 245
°
C (Pb-free
process)
– for all the BGA packages
– for packages with a thickness
≥
2.5 mm
– for packages with a thickness < 2.5 mm and a
volume
≥
350 mm
3
so called thick/large packages.
below 235
°
C (SnPb process) or below 260
°
C (Pb-free
process) for packages with a thickness < 2.5 mm and a
volume < 350 mm
3
so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing,
must be respected at all times.
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250
°
C or 265
°
C, depending on solder
material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| 74HC20D-T | Dual 4-input NAND Gate |
| 74HCT21N | IC HIGH SPEED CMOS LOGIK N/DIP14 |
| 74HCT21D-T | Dual 4-input AND Gate |
| 74HCT21D | Dual 4-input AND Gate |
| 74HCT283D-T | Binary Adder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 74HC21D(BJ) | 功能描述:AND Gate IC 2 Channel 14-SOIC 制造商:toshiba semiconductor and storage 系列:74HC 包裝:剪切帶（CT） 零件狀態:在售 邏輯類型:與門 電路數:2 輸入數:4 特性:- 電壓 - 電源:2 V ~ 6 V 電流 - 靜態（最大值）:1μA 電流 - 輸出高，低:5.2mA，5.2mA 邏輯電平 - 低:0.5 V ~ 1.8 V 邏輯電平 - 高:1.5 V ~ 4.2 V 不同 V，最大 CL 時的最大傳播延遲:17ns @ 6V，50pF 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 供應商器件封裝:14-SOIC 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 標準包裝:1 |
| 74HC21D,652 | 功能描述:邏輯門 DUAL 4-INPUT NAND GATE RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel |
| 74HC21D,653 | 功能描述:邏輯門 DUAL 4-INPUT NAND GATE RoHS:否 制造商:Texas Instruments 產品:OR 邏輯系列:LVC 柵極數量:2 線路數量（輸入/輸出）:2 / 1 高電平輸出電流:- 16 mA 低電平輸出電流:16 mA 傳播延遲時間:3.8 ns 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:DCU-8 封裝:Reel |
| 74HC21D,653-CUT TAPE | 制造商:NXP 功能描述:74HC21 Series 6 V Surface Mount Dual 4-Input AND Gate - SOIC-14 |
| 74HC21D | 制造商:NXP Semiconductors 功能描述:IC 74HC CMOS SMD 74HC21 SOIC14 |
發布緊急采購，3分鐘左右您將得到回復。