參數資料
型號： 78Q8430-100IGT/F
廠商： Maxim Integrated Products
文件頁數： 26/88頁
文件大?。?/td> 0K
描述： IC LAN MEDIA ACCESS CTLR 100LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
控制器類型： 以太網控制器，MAC/PHY
電源電壓： 3.3V
電流 - 電源： 230mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
78Q8430 Data Sheet
DS_8430_001
32
Rev. 1.2
same time then the actual value placed into the counter is the CDR value plus one to prevent the loss of
any countable events.
6.6.3
Precision Counting
Applications that require a high degree of temporal precision across all the counters can use the CMR for
this purpose.
Bit two of the CMR is the Freeze bit. The Freeze bit can be used when the values of many or all counters
must be known at an exact point in time. Setting the Freeze bit in the CMR will cause all counters to stop
counting at that moment. Any countable events that occur after the Freeze bit is set are stored in an
event FIFO. After the application has set the CMR Freeze bit, it should read all the counter values as
quickly as possible. The event FIFOs are deep enough to hold off countable events for up to 28
microseconds assuming minimum sized frames are ingressing and or egressing at full 100 Mbps data
rate, or 280 microseconds for 10 Mbps. When the application has finished reading the counter values, it
should clear the CMR Freeze bit. All of the events stored in the FIFOs will be counted at that time. If any
event FIFO fills before the application has cleared the CMR Freeze bit, then the hardware will auto-clear
the freeze condition and count all events in the event FIFOs. To check for this condition, the application
can query the CMR Freeze bit before clearing it. If it is already clear then the freeze condition had to be
cleared by hardware in order to avoid losing any counts. In this case, not all of the counters read are
guaranteed to be at their frozen value.
In the case that the application wants to start all the counters counting at the same time, the CMR
provides a Clear Receive bit and a Clear Transmit bit. These bits are write only, they will always read
back zero. When one is set, it causes all the read or write counters to be reset to zero at exactly the
same time.
6.6.4
Rollover Interrupts
For applications that only need a much more coarse counter treatment, rollover interrupts are provided for
each counter. The counter rollover interrupts can be individually enabled or disabled for each counter. In
some cases it may be desirable to preload a counter with a nonzero value to set how many counts, it will
take to roll the counter and trigger an interrupt.
The rollover indication for transmit counters zero through fourteen are bits zero through fourteen of the
TRIR respectively. The rollover indication for receive counters fifteen through thirty-nine are bits zero
through twenty-four of the RRIR respectively.
Each transmit and receive rollover bit can be individually enabled or disabled in terms of triggering a host
interrupt. When a rollover bit is set then the RMON bit of the HIR will be set unless the mask bit
corresponding to the rollover bit is clear. The RMON bit of the HIR will, in turn, trigger a host interrupt
when its corresponding mask bit is set.
6.7
Packet Classification
The packet classification engine is comprised of a content addressable memory (CAM) linked to control
logic (WCS), which is responsible for acting on the CAM result and generating the next CAM reference
word. The WCS applies the first byte of packet data to the CAM using a previous hit value of zero. The
resulting CAM address is then used to index a control word for the control logic to process. The control
logic then uses the control word along with the CAM address and the next packet byte to generate
another reference word to apply to the CAM. This process iterates until the packet is done or the control
word calls for completion. The final classification result is the address of the last CAM hit.
相關PDF資料
PDF描述
A1020B-1CQ84C IC FPGA 2K GATES 84-CQFP COM
A1225A-1PQ100C IC FPGA 2500 GATES 100-PQFP COM
A1440A-1VQG100I IC FPGA 4K GATES 100-VQFP
A3P1000-1FGG484T IC FPGA 1KB FLASH 1M 484-FBGA
A3PE1500-PQG208 IC FPGA 444I/O 208PQFP
相關代理商/技術參數
參數描述
78Q8430-100IGTR/F 功能描述:以太網 IC 10/100 Ethernet MAC & PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
78Q8430-128CGT/F 制造商:Maxim Integrated Products 功能描述:Ethernet ICs 10/100 Ethernet MAC & PHY
78Q8430-128CGTR/F 制造商:Maxim Integrated Products 功能描述:Ethernet ICs 10/100 Ethernet MAC & PHY
78Q8430-ARM9-EVM 功能描述:EVALUATION MODULE 78Q8430 ARM9 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
78Q8430EBST#DB 功能描述:以太網開發工具 3-in-1 Silicon Delay Line RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*