- 您現在的位置：買賣IC網 > PDF目錄382826 > 79RC32T355-133DH (INTEGRATED DEVICE TECHNOLOGY INC) IDT Interprise Integrated Communications Processor PDF資料下載
參數資料
| 型號： | 79RC32T355-133DH |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | IDT Interprise Integrated Communications Processor |
| 中文描述： | 32-BIT, 133 MHz, RISC PROCESSOR, PQFP208 |
| 封裝： | 28 X 28 MM, 3.40 MM HEIGHT, PLASTIC, MO-143FA-1, QFP-208 |
| 文件頁數： | 37/47頁 |
| 文件大小： | 987K |
| 代理商： | 79RC32T355-133DH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
37 of 47
May 25, 2004
IDT 79RC32355
Table 16 shows the pin numbering for the Standard EJTAG connector. All the even numbered pins are connected to ground. Multiplexing of pin
functions should be considered when connecting
EJTAG_TRST_N and EJTAG_PCST.
For details on using the JTAG connector, see the JTAG chapters in the RC32355 user reference manual.
AC Test Conditions
Figure 21 Output Loading for AC Timing
PIN
SIGNAL
RC32355 I/O
TERMINATION
1
1.
The value of the series resistor may depend on the actual printed circuit board layout situation.
2.
JTAG_TCK pull-up resistor is not required according to the JTAG (IEEE1149) standard. It is indicated here to prevent a floating CMOS input when the EJTAG connector is
unconnected.
1
EJTAG_TRST_N
Input
10 k
pull-down resistor. A pull-down resistor will hold the EJTAG controller in reset when not in use
if the EJTAG_TRST_N function is selected with the boot configuration vector. Refer to the User Man-
ual.
3
JTAG_TDI
Input
10 k
pull-up resistor
5
JTAG_TDO
Output
33
series resistor
7
JTAG_TMS
Input
10 k
pull-up resistor
9
JTAG_TCK
Input
10 k
pull-up resistor
2
11
System Reset
Input
10 k
pull-up resistor is used if it is combined with the system cold reset control, COLDRSTN.
13
EJTAG_PCST[0]
Output
33
series resistor
15
EJTAG_PCST[1]
Output
33
series resistor
17
EJTAG_PCST[2]
Output
33
series resistor
19
EJTAG_DCLK
Output
33
series resistor
21
Debug Boot
Input
This can be connected to the boot configuration vector to control debug boot mode if desired. Refer
to Table 2 on page 12 and the RC32355 user reference manual.
23
V
CC
I/O
Output
Used to sense the circuit board power. Must be connected to the VCC I/O supply of the circuit board.
Table 16 Pin Numbering of the JTAG and EJTAG Target Connector
1.5V
Parameter
Value
Units
Input pulse levels
0 to 3.0
V
Input rise/fall
3.5
ns
Input reference level
1.5
V
Output reference levels
1.5
V
AC test load
25
pF
RC32355
Output
.
50
50
Test
Point
相關PDF資料 |
PDF描述 |
|---|---|
| 79RC32T355-133DHI | IDT Interprise Integrated Communications Processor |
| 79RC32T355-150DH | IDT Interprise Integrated Communications Processor |
| 79RC32T355-150DHI | IDT Interprise Integrated Communications Processor |
| 79RC32T355-180DH | IDT Interprise Integrated Communications Processor |
| 79RC32T355-180DHI | IDT Interprise Integrated Communications Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 79RC32T355-133DHG | 制造商:Integrated Device Technology Inc 功能描述:MPU RC32300 RISC 32-Bit 133MHz 3.3V 208-Pin PQFP |
| 79RC32T355-133DHGI | 制造商:Integrated Device Technology Inc 功能描述:MPU RC32300 RISC 32-Bit 133MHz 3.3V 208-Pin PQFP |
| 79RC32T355133DHI | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:Communications Processor |
| 79RC32T355-133DHI | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:Communications Processor |
| 79RC32T355150DH | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:Communications Processor |
發布緊急采購，3分鐘左右您將得到回復。