- 您現在的位置：買賣IC網 > PDF目錄7077 > 8344 (3M)WORKSURFACE RIGID ESD DISSP GRAY PDF資料下載
參數資料
| 型號： | 8344 |
| 廠商： | 3M |
| 文件頁數： | 12/16頁 |
| 文件大小： | 0K |
| 描述： | WORKSURFACE RIGID ESD DISSP GRAY |
| 標準包裝： | 1 |
| 系列： | 8300 |
| 墊子類型： | 桌子，工作臺 |
| 形狀： | 矩形 |
| 長度： | 3'（0.91m） |
| 寬： | 2'（0.61m） |
| 厚度： | 0.13"（3.30mm） |
| 顏色： | 灰 |
| 材質： | Laminate |
| 特點： | 耗散 |
| 包括： | 接地軟線，接地卡扣 |
| 其它名稱： | 05400718619 98079815852 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁
78-8136-3801-8
A.
Both the laminate and the substrate should be conditioned at approximately 75°F (24°C) and 4555%
RH for a minimum of 48 hours prior to fabrication.
B.
Provision should be made to allow air circulation around the various components of the fabrication
process (i.e., laminate, substrate, etc.).
C.
Where cracking may be a problem due to moisture differentials, the laminate should be thoroughly
dried out to minimize the rate of shrinkage. Fabricators have not experienced problems with buckling
or lifting of laminate when the laminate was dried prior to lamination and then later took on moisture.
(Note: Moisture in the laminate enhances its postforming properties.)
D.
Decreasing the ambient humidity minimizes stress cracking
Increasing the ambient humidity facilitates postforming
7.0
Fabrication
3M Rigid Worksurface 8300 Series is a rigid product and the top surface is very hard. Special tools and
procedures are required in order to fabricated this product successfully.
A.
Cutting/sawing/routing:
1. To avoid chipping during sawing, it is important that the rotation of the blade be such that the teeth of
the blade first contact and cut into the decorative (top) surface of the laminate. Therefore, with a hand
circular saw, the laminate should be cut with the decorative surface face down. With a table saw, the
decorative surface should face up.
2. Blades and bits used should be carbidetipped. A blade with more teeth will make a smoother cut.
Blades/bits should always be sharp. Recommended saw blades: triple chip grind, 10 – 15 degrees
positive rake. Ten inch diameter minimum 80 teeth, twelve inch diameter minimum 100 teeth.
3. The higher the rotation speed of the blade or bit, the cleaner the cut will be.
Caution: Do not exceed manufacturers recommended rotation speeds.
4. The laminate should not be forced into a cutting blade, and it must be supported near the blade,
especially when cutting unmounted laminate.
5. When cutting openings into a finished benchtop covered with laminate, never cut the inside corners
of the opening at 90° (the point at which each such cut ends can serve as a source for a crack.)
Always round such inside corners to a minimum radius to 0.125 in. (3.2 mm). However, the largest
possible radius should be used.
6. After cutting/sawing/routing, the edges of the laminate should always be filed or sanded to remove
chips or nicks that may lead to a crack later on.
B.
Sanding:
Sanding and filing should always be directed parallel to or away from the decorative surface.
C.
Drilling:
Recommendations are generally the same as those for sawing. In addition, the material being drilled
should be backed to prevent breakout at the bottom of the hole.
8.0
Postforming
A.
The minimum radius around which 3M Rigid Worksurface 8300 should be formed is 0.50 in. when
parallel to the machine direction. If the laminate is postformed perpendicular to the machine direction
the minimum radius is 0.625 in.
B.
Laminate sheets can be formed only in a straight line. They cannot be drawn over curved edges (e.g.,
covering a round tabletop) like vacuumformable plastic sheets can. The substrate must be clean,
smooth, and straight. Parallelism is essential in the moving parts of the forming operation.
C.
In general, the laminate should be only slightly larger than the substrate [0.1250.25 in. (3.26.4 mm)]
and should be trimmed after the forming operation is completed. Excessive overhang will tend to crack
or buckle during the postforming process. Check the edges of the laminate prior to forming. Any nicks
or cracks should be filed smooth before forming; if not, cracks can develop at these rough spots.
相關PDF資料 |
PDF描述 |
|---|---|
| 8343 | WORKSURFACE RIGID ESD DISSP BGE |
| 2-1419104-2 | RELAY GEN PURPOSE SPST 30A 48V |
| 431301-23-0 | TERM BARRIER 23CIRC 1 ROW .4375 |
| V23061B1005A301 | RELAY GEN PURPOSE SPDT 8A 12V |
| GP1500R-0.010-02-0816 | THERMAL PAD .010" 8"X16" GP1500R |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 83440 00000020 05 | 功能描述:工業壓力 / 力傳感器 PRESSURE SWITCH RoHS:否 制造商:Honeywell 工作壓力:0 bar to 25 bar 壓力類型:Sealed Gauge 準確性:0.25 % 輸出類型: 安裝風格:Screw 工作電源電壓:8 V to 30 V 輸出電壓:8 V to 30 V 封裝: |
| 83440-00000020-05 | 功能描述:板上安裝壓力/力傳感器 PRESSURE SWITCH RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| 834402 | 制造商:Whirlpool 功能描述:KNOB, SURFACE *NLA 08/06* |
| 8-34404-2 | 制造商:TE Connectivity 功能描述:TERMINAL,BUDG R 12-10 8 - Bulk |
| 834-40CM-9.5 | 制造商:NORTH SAFETY PRODUCTS 功能描述:GLOVE GAUNTLET CHEM RES 40CM (1PR) |
發布緊急采購，3分鐘左右您將得到回復。