參數資料
型號： 935263156557
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP80
封裝： PLASTIC, QFP-80
文件頁數： 26/76頁
文件大?。?/td> 567K
代理商： 935263156557
Philips Semiconductors
Product specification
P83C557E4/P80C557E4/P89C557E4
Single-chip 8-bit microcontroller
1999 Mar 02
32
The Control Register, S1CON:
The CPU can read from and write to this 8-bit, directly addressable
SFR. Two bits are affected by the SIO1 hardware: the SI bit is set
when a serial interrupt is requested, and the STO bit is cleared when
a STOP condition is present on the I2C bus. The STO bit is also
cleared when ENS1 = 0.
Figure 30. Serial control (S1CON) register.
7
6
54
321
0
S1CON (D8H)
CR2
ENS1
STA
STO
SI
AA
CR1
CR0
Table 24.
Description of S1CON bits
SYMBOL
BIT
FUNCTION
CR2
S1CON.7
Clock rate bit 2, see Table 25.
ENS1
S1CON.6
ENS1 = 0:
Serial I/O
disabled and reset. SDA and SCL outputs are high-Z.
ENS1 = 1:
Serial I/O
enabled.
STA
S1CON.5
START flag. When this bit is set in slave mode, the hardware checks the I2C bus and generates a START
condition if the bus is free or after the bus becomes free. If the device operates in master mode it will
generate a repeated START condition.
STO
S1CON.4
STOP flag. If this bit is set in a master mode a STOP condition is generated. A STOP condition detected on
the I2C bus clears this bit. This bit may also be set in slave mode in order to recover from an error
condition. In this case no STOP condition is generated to the I2C bus, but the hardware releases the SDA
and SCL lines and switches to the not selected receiver mode. The STOP flag is cleared by the hardware.
SI
S1CON.3
Serial Interrupt flag. This flag is set, and an interrupt request is generated, after any of the following events
occur:
– A START condition is generated in master mode.
– The own slave address has been received during AA = 1.
– The general call address has been received while S1ADR.0 and AA = 1.
– A data byte has been received or transmitted in master mode (even if arbitration is lost).
– A data byte has been received or transmitted as selected slave.
– A STOP or START condition is received as selected slave receiver or transmitter.
While the SI flag is set, SCL remains LOW and the serial transfer is suspended. SI must be reset by software.
AA
S1CON.2
Assert Acknowledge flag. When this bit is set, an acknowledge is returned after any one of the following
conditions:
– Own slave address is received.
– General call address is received (S1ADR.0 = 1).
– A data byte is received, while the device is programmed to be a master receiver.
– A data byte is received. while the device is a selected slave receiver.
When the bit is reset, no acknowledge is returned. Consequently, no interrupt is requested when the own
address or general call address is received.
CR1
CR0
S1CON.1
S1CON.0
Clock rate bits 1 and 0, see Table 25.
相關PDF資料
PDF描述
935263261557 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80
935263206557 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80
935268065557 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80
935263263557 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80
935263262557 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
935264217557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935267356112 制造商:NXP Semiconductors 功能描述:IC TEA1507PN
935268081112 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935268721125 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R
935269304128 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*