參數資料
型號: 935265290112
廠商: NXP SEMICONDUCTORS
元件分類: 接收器
英文描述: AM/FM, AUDIO DEMODULATOR, PDIP42
封裝: 0.600 INCH, PLASTIC, SDIP-42
文件頁數: 26/71頁
文件大小: 304K
代理商: 935265290112
2000 Aug 04
32
Philips Semiconductors
Product specication
Digital TV sound demodulator/decoder
TDA9874A
7.3.12
NICAM CONFIGURATION REGISTER (NCONR)
The default setting after Power-on reset is 0000 0000.
Table 38 NICAM conguration register (subaddress 14)
Table 39 Description of the NICAM conguration register bits; see notes 1 to 4
Notes
1. The decision of whether auto-muting is permitted will be taken by the controlling microprocessor based on
information contained in the TDA9874A’s status registers. Thus, it depends on the strategy implemented in the
software whether the auto-mute function is in accordance with
“NICAM 728 ETS Revised for Data Applications” or
any other preference.
2. The NICAM de-emphasis gain is 0 dB at 40 Hz.
3. The bit AMSEL has only an effect on the analog sound outputs (pins OUTL, OUTR and OUTM). With regard to the
digital sound output (I2S-bus), the auto-mute will only switch between NICAM and the first sound carrier.
4. The DCXO test mode is intended for checking the DCXO control range with the actually used PCB layout and crystal
type. During normal operation, the DCXO test mode should not be used.
76543210
DCXOPULL
DCXOTEST
0
DOUTEN
0
AMSEL
NDEEM
AMUTE
BIT
SYMBOL
DESCRIPTION
7
DCXOPULL
DCXO frequency select: this bit selects the DCXO lower or upper test frequency during
DCXO test mode. If bit DCXOPULL = 1 it sets the DCXO to the lower DCXO frequency.
If bit DCXOPULL = 0 it sets the DCXO to its higher frequency.
6
DCXOTEST
DCXO test mode enable: if bit DCXOTEST = 1 it enables the DCXO test mode
(available only during FM mode). In this mode frequency pulling via bit DCXOPULL is
enabled. If bit DCXOTEST = 0 it enables normal operation.
5
this bit is not used and should be set to logic 0
4
DOUTEN
Data output enable: if bit DOUTEN = 1 it enables the output of the NICAM serial data
stream from the DQPSK demodulator and of the associated clock, PCLK.
If bit DOUTEN = 0 both outputs will be 3-stated.
3
this bit is not used and should be set to logic 0
2
AMSEL
Auto-mute select: if bit AMSEL = 1 the auto-mute will switch between NICAM sound and
the analog mono input. This bit only has an effect when the auto-mute function is
enabled and when the DAC has been selected in the analog output select register
(see Section 7.3.18). If bit AMSEL = 0 the auto-mute will switch between NICAM sound
and the sound on the rst sound carrier (i.e. FM mono or AM).
1
NDEEM
De-emphasis on/off: if bit NDEEM = 1 it switches the NICAM J17 de-emphasis off.
If bit NDEEM = 0 it switches the NICAM J17 de-emphasis on.
0
AMUTE
Auto-muting on/off: if bit AMUTE = 1 automatic muting is disabled. This bit only has an
effect when the second sound carrier is set to NICAM. If bit AMUTE = 0 it enables the
automatic switching between NICAM and the program on the rst sound carrier (i.e.
FM mono or AM), depending on the NICAM bit error rate. The FM dematrix should be
set to the mono position or IDSWFM (subaddress 11) should be set.
相關PDF資料
PDF描述
93526374518 FM, AUDIO DEMODULATOR, PQFP44
93526374557 FM, AUDIO DEMODULATOR, PQFP44
935263897551 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP32
935263898112 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28
935263897518 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP32
相關代理商/技術參數
參數描述
935267356112 制造商:NXP Semiconductors 功能描述:IC TEA1507PN
935268081112 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935268721125 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R
935269304128 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP
935269544557 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-2US1-V1.3