參數資料
型號： 935266795557
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQCC68
封裝： PLASTIC, LCC-68
文件頁數： 66/112頁
文件大?。?/td> 693K
代理商： 935266795557
1996 Jun 27
57
Philips Semiconductors
Product specication
8-bit microcontroller with on-chip CAN
P8xC592
13.6.3
REMOTE FRAME
A CAN-controller acting as a receiver for certain
information may initiate the transmission of the respective
data by transmitting a Remote Frame to the network,
addressing the data source via the Identifier and setting
the RTR bit HIGH (remote; recessive bus level). The
Remote Frame is similar to the Data Frame with the
following exceptions:
RTR bit is set HIGH
Data Length Code is ignored
No Data Field contained.
Note that the value of the Data Length Code should be the
one of the corresponding Data Frame, although it is
ignored for a Remote Frame.
A Remote Frame is composed of six different bit fields:
Start-of-Frame
Arbitration Field
Control Field
CRC Field
Acknowledge Field
End-Of-Frame.
See Section 13.6.2 for more detailed explanation of the
Remote Frame bit fields.
13.6.4
ERROR FRAME
The Error Frame consists of two different fields:
The first field, accomplished by the superimposing of
Error Flags contributed from different CAN-controllers
The second field is the Error Delimiter.
13.6.4.1
Error Flag
There are two forms of an Error Flag:
Active Error Flag, consists of six consecutive
dominant bits.
Passive Error Flag, consists of six consecutive
recessive bits unless it is overwritten by dominant bits
from other CAN-controllers.
An error-active CAN-controller (see Section 13.6.9)
detecting an error condition signals this by transmission of
an Active Error Flag. This Error Flag's form violates the
bit-stuffing rule (see Section 13.6.7) applied to all fields,
from Start-Of-Frame to CRC Delimiter, or destroys the
fixed form of the fields Acknowledge Field or
End-Of-Frame (see Fig.20).
Consequently, all other CAN-controllers detect an error
condition and start transmission of an Error Flag.
Therefore the sequence of dominant bits, which can be
monitored on the bus, results from a superposition of
different Error Flags transmitted by individual
CAN-controllers. The total length of this sequence varies
between six (minimum) and twelve (maximum) bits.
An error-passive CAN-controller (see Section 13.6.9)
detecting an error condition tries to signal this by
transmission of a Passive Error Flag. The error-passive
CAN-controller waits for six consecutive bits with identical
polarity, beginning at the start of the Passive Error Flag.
The Passive Error Flag is complete when these six
identical bits have been detected.
13.6.4.2
Error Delimiter
The Error Delimiter consists of eight recessive bits and has
the same format as the Overload Delimiter. After
transmission of an Error Flag, each CAN-controller
monitors the bus-line until it detects a transition from a
dominant-to-recessive bit level. At this point in time, every
CAN-controller has finished sending its Error Flag and has
additionally sent the first out of the 8 recessive bits of the
Error Delimiter. Afterwards all CAN-controllers transmit the
remaining recessive bits. After this event and an
Intermission Field all error-active CAN-controllers within
the network can start a transmission simultaneously.
If a detected error is signalled during transmission of a
Data Frame or Remote Frame, the current message is
spoiled and a retransmission of the message is initiated.
If a CAN-controller monitors any deviation of the Error
Frame, a new Error Frame will be transmitted. Several
consecutive Error Frames may result in the CAN-controller
becoming error-passive and leaving the network
unblocked.
In order to terminate an Error Flag correctly, an
error-passive CAN-controller requires the bus to be
Bus-Idle (see Section 13.6.6) for at least three bit periods
(if there is a local error at an error-passive-receiver).
Therefore a CAN-bus should not be 100% permanently
loaded.
相關PDF資料
PDF描述
935086530512 8-BIT, 16 MHz, MICROCONTROLLER, PQCC68
935210470512 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQCC68
935089010512 8-BIT, 16 MHz, MICROCONTROLLER, PQCC68
935085020512 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQCC68
067201.5 Circular Connector; Body Material:Aluminum; Series:PT06; No. of Contacts:2; Connector Shell Size:8; Connecting Termination:Solder; Circular Shell Style:Straight Plug; Circular Contact Gender:Socket; Insert Arrangement:8-2
相關代理商/技術參數
參數描述
935267356112 制造商:NXP Semiconductors 功能描述:IC TEA1507PN
935268081112 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935268721125 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R
935269304128 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP
935269544557 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-2US1-V1.3
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*